Filter
Top Products
3 - 54
3 POSITIONING DEDICATED SIGNALS
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
Axis 16 Axis 15 Axis 14 Axis 13 Axis 12 Axis 11 Axis 10 Axis 9 Axis 8 Axis 7 Axis 6 Axis 5 Axis 4 Axis 3 Axis 2 Axis 1
Axis 32 Axis 31 Axis 30 Axis 29 Axis 28 Axis 27 Axis 26 Axis 25 Axis 24 Axis 23 Axis 22 Axis 21 Axis 20 Axis 19 Axis 18 Axis 17
Axis 16 Axis 15 Axis 14 Axis 13 Axis 12 Axis 11 Axis 10 Axis 9 Axis 8 Axis 7 Axis 6 Axis 5 Axis 4 Axis 3 Axis 2 Axis 1
Axis 32 Axis 31 Axis 30 Axis 29 Axis 28 Axis 27 Axis 26 Axis 25 Axis 24 Axis 23 Axis 22 Axis 21 Axis 20 Axis 19 Axis 18 Axis 17
Axis 16 Axis 15 Axis 14 Axis 13 Axis 12 Axis 11 Axis 10 Axis 9 Axis 8 Axis 7 Axis 6 Axis 5 Axis 4 Axis 3 Axis 2 Axis 1
Axis 32 Axis 31 Axis 30 Axis 29 Axis 28 Axis 27 Axis 26 Axis 25 Axis 24 Axis 23 Axis 22 Axis 21 Axis 20 Axis 19 Axis 18 Axis 17
D714
D715
D716
D717
D718
D719
P1
P2
P3
(Note-1) : Make the axis No. controlled with the manual pulse generator
setting with 1/0.
1 : Specified axis
0 : Unspecified axis
(
Note-2
)
: The ran
g
e of axis No.1 to 8 is valid in the Q172HCPU.
(b) Refer to Section 6.22 for details of the manual pulse generator operation.
(4) Manual pulse generator 1-pulse input magnification setting
registers (D720 to D751) ..................................... Command device
(a) These register set the magnification (1 to 10000) per pulse of number of the
input pulses from manual pulse generator at the pulse generator operation.
1-pulse input
magnification
setting register
Axis No. Setting range
1-pulse input
magnification
setting register
Axis No. Setting range
D720 Axis 1 D736 Axis 17
D721 Axis 2 D737 Axis 18
D722 Axis 3 D738 Axis 19
D723 Axis 4 D739 Axis 20
D724 Axis 5 D740 Axis 21
D725 Axis 6 D741 Axis 22
D726 Axis 7 D742 Axis 23
D727 Axis 8 D743 Axis 24
D728 Axis 9 D744 Axis 25
D729 Axis 10 D745 Axis 26
D730 Axis 11 D746 Axis 27
D731 Axis 12 D747 Axis 28
D732 Axis 13 D748 Axis 29
D733 Axis 14 D749 Axis 30
D734 Axis 15 D750 Axis 31
D735 Axis 16
1 to 10000
D751 Axis 32
1 to 10000
(Note-1): The range of axis No.1 to 8 is valid in the Q172HCPU.
(b) Refer to Section 6.22 for details of the manual pulse generator operation.