Filter
Top Products
M400E Ozone Analyzer Operator’s Manual Table of Contents
Table 6-2: Test Functions Defined................................................................................................................61
Table 6-3: Warning Messages Defined.........................................................................................................62
Table 6-4: Primary Setup Mode Features and Functions.............................................................................64
Table 6-5: Secondary Setup Mode Features and Functions ........................................................................64
Table 6-6: Password Levels..........................................................................................................................66
Table 7-1: Front Panel LED Status Indicators for iDAS................................................................................77
Table 7-2: iDAS Data Channel Properties ....................................................................................................78
Table 7-3: iDAS Data Parameter Functions..................................................................................................85
Table 7-4: Variable Names (VARS)..............................................................................................................94
Table 7-5: Diagnostic Mode (DIAG) Functions .............................................................................................96
Table 7-6: DIAG - Analog I/O Functions .......................................................................................................98
Table 7-7: Voltage Tolerances for the TEST CHANNEL Calibration......................................................... 103
Table 7-8: Current Loop Output Check...................................................................................................... 107
Table 7-9: Analog Output Voltage Range Min/Max ................................................................................... 108
Table 7-10: Test Channels Functions available on the M400E’s Analog Output ........................................ 111
Table 8-1: COMM Port Communication Modes......................................................................................... 119
Table 8-2: Terminal Mode Software Commands ....................................................................................... 123
Table 8-3: Teledyne Instruments Serial I/O Command Types................................................................... 124
Table 8-4: Ethernet Status Indicators ........................................................................................................ 133
Table 8-5: LAN/Internet Configuration Properties...................................................................................... 134
Table 8-6: RS-232 Communication Parameters for Hessen Protocol ....................................................... 139
Table 8-7: Teledyne Instruments Hessen Protocol Response Modes ...................................................... 142
Table 8-8: Default Hessen Status Bit Assignments ................................................................................... 146
Table 9-1: AUTOCAL Modes ..................................................................................................................... 162
Table 9-2: AutoCal Attribute Setup Parameters......................................................................................... 163
Table 9-3: Example AutoCal Sequence..................................................................................................... 163
Table 10-1: Daily Activity Matrix................................................................................................................... 183
Table 10-2: Activity Matrix for Audit Procedure............................................................................................ 183
Table 10-3: Activity Matrix for Data Reduction, Validation and Reporting................................................... 184
Table 10-4: Activity Matrix for Calibration Procedures................................................................................. 184
Table 11-1: Relay PCA Status LED’s .......................................................................................................... 203
Table 11-2: Thermocouple Configuration Jumper (JP5) Pin-Outs............................................................... 205
Table 11-3: Thermocouple Settings for Optional Metal Wool Scrubber ...................................................... 205
Table 11-4: AC Power Configuration for Internal Pumps (JP7)................................................................... 208
Table 11-5: Power Configuration for Optional Metal Wool Scrubber Heater (JP6) ..................................... 209
Table 11-6: Front Panel Status LED’s ......................................................................................................... 215
Table 12-1: Predictive Uses for Test Functions........................................................................................... 219
Table 12-2: M400E Maintenance Schedule................................................................................................. 221
Table 13-1: Front Panel Warning Messages ............................................................................................... 235
Table 13-2: Test Functions - Indicated Failures........................................................................................... 237
Table 13-3: Test Channel Outputs as Diagnostic Tools .............................................................................. 239
Table 13-4: Relay PCA Watchdog LED Failure Indications......................................................................... 240
Table 13-5: Relay PCA Status LED Failure Indications............................................................................... 241
Table 13-6: DC Power Test Point and Wiring Color Codes......................................................................... 246
Table 13-7: DC Power Supply Acceptable Levels ....................................................................................... 247
Table 13-8: Relay PCA Control Devices...................................................................................................... 248
Table 13-9: Analog Output Test Function - Nominal Values Voltage Outputs ............................................ 250
Table 13-10: Status Outputs Check............................................................................................................... 251
Table 13-11: M400E Control Input Pin Assignments and Corresponding Signal I/O Functions ................... 252
Table 14-1: Static Generation Voltages for Typical Activities...................................................................... 259
Table 14-2: Sensitivity of Electronic Devices to Damage by ESD............................................................... 260
04315 Rev. C1 ix