Filter
Top Products
PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Song Mode
Song Play
[F1] PLAY
[F2] GROOVE
[F3] TRACK
[F6] CHAIN
Song Record
Song Record Standby
[F1] SETUP
[F2] VOICE
[F3] ARP ED
[F5] CLICK
[F6] ALL TR
During Song Recording
[F1] SETUP
[F3] REST
[F4] TIE
[F5] DELETE
[F6] BAK DEL
Arpeggio Edit
[F1] COMMON
[F2] TYPE
[F3] MAIN
[F4] LIMIT
[F5] PLAY FX
[F6] OUT CH
Song Edit
[F1] CHANGE
[F2] VIEW FLT
[F4] TR SEL
[F5] INSERT
[F6] DELETE
Song Job
[F1] UNDO/REDO
[F2] NOTE
[F3] EVENT
[F4] MEAS
[F5] TRACK
[F6] SONG
Supplementary Information
93
06: Thin Out
This Job thins out the specified type of continuous data in the specified range—allowing you to free up memory space
for other data or further recording.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, all) and range of measures/beats/clocks over which the Job is applied.
EventType
Determines the event type to be thinned.
Settings: PB (Pitch Bend), CC (Control Change)*, CAT (Channel Aftertouch), PAT (Polyphonic Aftertouch), TMP (Tempo)
* You can also specify the CC No. (Control Change number).
NOTE The Thin Out Job will not work on continuous data that has a clock interval of greater than 60 clocks per event.
07: Modify Control Data
This Job lets you change the values of a specified type of control change data (for example, pitch bend, control
change, aftertouch, etc.) in the specified range. Data changes are calculated as follows:
Modified value = (original value x Rate) + Offset.
Any result lower than the minimum is set to the minimum; any result higher than the maximum is set to the maximum.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, TMP, all) and range of measures/beats/clocks over which the Job is applied.
EventType
Determines the event type to be modified.
Settings: PB (Pitch Bend), CC (Control Change)*, CAT (Channel Aftertouch), PAT (Polyphonic Aftertouch), TMP (Tempo)
* You can also specify the CC No. (Control Change number).
SetAll
Sets all target events to the same fixed value. When set to “off” the Set All parameter has no effect. When set to a value
other than “off,” the Rate and Offset parameters are unavailable and appear as “***” on the display.
Settings: off, 000 -127 (-8192 – +0 – +8191 for pitch bend, 005.0 – 300.0 for tempo), ***
Rate
Determines the percentage by which the target events will be shifted from their original values. When the Set All
parameter is not set to “off,” this parameter appears as “***” and cannot be changed.
Settings: 000% – 200%, ***
Offset
Adds a fixed value to the Rate-adjusted event values. When the Set All parameter is not set to “off,” this parameter
appears as “***” and cannot be changed.
Settings: -127- +0 – +127 (-8192 – +0 – +8191 for pitch bend, -275 – +0 – +275 for tempo), ***
08: Beat Stretch
This Job performs time-expansion or compression over the selected range. Keep in mind that this operation affects all
event timing, note step times, and note gate times.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, all) and range of measures/beats/clocks over which the Job is applied.
Rate
Determines the amount of time expansion or compression as a percentage. Settings higher than 100% produce
expansion, and settings below 100% produce compression. A setting of 100 produces no change.
Settings: 025% – 400%