Filter
Top Products
PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Master Mode
Master Play
[F1] PLAY
[F2] MEMORY
[F3] ZONE SW
Master Edit
Common Edit
[F1] NAME
Zone Edit
[F1] TRANS
[F2] NOTE
[F3] TX SW
[F4] PRESET
[F5] KNOB
Master Job
[F1] INIT
[F4] BULK
131
From this display you can set how each individual zone affects transmission of various MIDI data, such as Control
Change and Program Change messages. When the relevant parameter is set to “on,” playing the selected zone will
transmit the corresponding MIDI data. Note that two different display types listed below are available and you can
switch between them by pressing the [SF6] button. Each display type features the same settings in a different format;
use the type you feel most comfortable with.
•Display showing four Zones
•Display showing all parameters for one Zone
Settings: See below.
Bank (TG) ................................Determines whether or not to transmit Bank Select MSB/LSB messages to the internal tone
generator.
PC (TG)....................................Determines whether or not to transmit Program Change messages to the internal tone generator.
Bank (MIDI) .............................Determines whether or not to transmit Bank Select MSB/LSB messages to the internal tone
generator.
PC (MIDI).................................Determines whether or not to transmit Program Change messages to the external tone
generator via MIDI.
PB (Pitch Bend).......................Determines whether or not to transmit Pitch Bend messages to the internal and external tone
generator.
MW (Modulation Wheel)..........Determines whether or not to transmit MIDI messages generated by using the Modulation
Wheel to the internal and external tone generator.
FC1 (Foot Controller 1)............Determines whether or not to transmit MIDI messages generated by pressing the optional Foot
Controller to the internal and external tone generator.
Sus (Sustain) ...........................Determines whether or not to transmit Control Number 64 (Sustain) messages to the internal and
external tone generator. This parameter is not available for the Drum Voice Parts.
FS (Foot Switch) ......................Determines whether or not to transmit MIDI messages generated by pressing the Footswitch
connected to the FOOT SWITCH [ASSIGNABLE] jack to the internal and external tone
generator.
Knob........................................Determines whether or not to transmit MIDI messages generated by using the Knobs to the
internal and external tone generator.
A.Func1 (Assignable Function 1) /A.Func2 (Assignable Function 2)
.................................................Determines whether or not to transmit MIDI messages generated by pressing the ASSIGNABLE
FUNCTION [1] and [2] buttons to the internal tone generator.
Vol/Exp (Volume/Expression)... Determines whether or not to transmit volume messages to the internal and external tone
generator.
Pan ..........................................Determines whether or not to transmit Pan messages to the internal and external tone generator.
From this display you can make Voice-related settings for each Zone in the selected Master program number.
NOTE
By using the [F6] SEND button, you can select whether the settings in PRESET display are immediately applied or not. If the [F6]
SEND button is turned on ( ), the relevant MIDI messages will be output from the MOXF6/MOXF8 as soon as you
change each parameter in this display. If the [F6] SEND button is turned off ( ), the MIDI messages will be output from
the MOXF6/MOXF8 after you store the edited Master and then select the Master again. However, the parameters set to off in the
[F1]TRANS or [F3]TX SW display cannot be output.
BankMSB (Bank Select MSB)
BankLSB (Bank Select LSB)
PgmChange (Program Change)
Determines the Voice assignment for each Zone in the selected Master.
Settings: See the “Voice List” in the “Data List” PDF document.
Volume
Determines the output level of the Voice in each Zone.
Settings: 0 – 127
Pan
Determines the stereo pan position of the Voice in each Zone.
Settings: L64 (far left) – C (center) – R63 (far right)
[F3] TX SW (Transmit Switch)
[F4] PRESET