Filter
Top Products
PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Performance Mode
Performance Play
[F1] PLAY
[F2] VOICE
[F3] PORTA
[F4] EG
[F5] ARP ED
[F6] EFFECT
Arpeggio Edit
[F1] COMMON
[F2] TYPE
[F3] MAIN
[F4] LIMIT
[F5] PLAY FX
[F6] OUT CH
Performance Edit
Common Edit
[F1] GENERAL
[F2] OUT/MFX
[F3] MEQ
[F4] USB I/O
[F5] A/D IN
[F6] EFFECT
Part Edit
[F1] VOICE
[F2] OUTPUT
[F3] EQ
[F4] TONE
[F5] RCV SW
Performance Job
[F1] INIT
[F2] RECALL
[F3] COPY
[F4] BULK
Performance Record
[F1] SETUP
[F2] REC TR
[F3] OTHER
[F5] CLICK
[F6] INFO
Supplementary Information
66
VelSensOfs (Velocity Sensitivity Offset)
Determines the amount by which played velocities are adjusted for the actual resulting velocity effect. This lets you raise
or lower all velocities by the same amount—allowing you to automatically compensate for playing too strongly or too
softly.
Settings: 0 – 127
[SF6] OTHER
PB Upper (Pitch Bend Range Upper)
PB Lower (Pitch Bend Range Lower)
Determines the maximum pitch bend range for each Part in semitones. This is the same as in Voice Common Edit. See
page 31.
Settings: -48 semi – +0 semi – +24 semi
Assign 1 (Assign 1 Value)
Assign 2 (Assign 2 Value)
Determines the offset value by which the functions assigned to the ASSIGN 1/2 knobs will be shifted from their original
settings. The ASSIGN 1/2 knobs’ functions are set in the CTL SET display (page 32) of Voice Common Edit.
Settings: -64 – +0 – +63
[SF1] VOL/PAN (Volume/Pan)
Volume
Determines the volume for each part, allowing you to set the optimum level balance of all the Parts.
Settings: 0 – 127
Pan
Determines the stereo pan position for each Part.
Settings: L63 (far left) – C (center) – R63 (far right)
VoiceELPan (Voice Element Pan)
Determines whether the individual pan settings for each Voice (made via [VOICE] [EDIT] Element selection [F4]
AMP [SF1] LVL/PAN Pan) are applied or not. When this is set to “off,” the pan position for the each Element is set to
center in the Part.
Settings: off, on
[SF2] EF SEND (Effect Send)
From this display you can set the Send Level and Dry Level sent to the System Effects for each Part. For details about
the effect connection in the Performance mode, see page 20.
ChoSend (Chorus Send)
Determines the volume for each Part. This lets you make detailed balance adjustments among the various sounds of the
Drum Voice.
Settings: 0 – 127
[F2] OUTPUT
127
0 12764
12764
127
64
127
0
127
0
When Depth (above)
= 64 and Offset =32
When Depth (above)
= 64 and Offset =64
When Depth (above)
= 64 and Offset =96
Actual
resulting
velocity
(affecting
the tone
generator)
Actual
resulting
velocity
(affecting
the tone
generator)
Velocity with which you play a note
Velocity with which you play a note
Velocity with which you play a note
Actual
resulting
velocity
(affecting
the tone
generator)
Knob
Knob
Knob
Knob
Knob