Filter
Top Products
PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Mixing Mode
Mixing Play
[F1] VOL/PAN
[F2] VOICE
[F3] EF SEND
[F4] TEMPLATE
[F5] VCE ED
[F6] EFFECT
Mixing Edit
Common Edit
[F1] GENERAL
[F2] MFX
[F3] MEQ
[F4] USB I/O
[F5] A/D IN
[F6] EFFECT
Part Edit
[F1] VOICE
[F2] OUTPUT
[F3] EQ
[F4] TONE
[F5] RCV SW
Mixing Job
[F1] INIT
[F2] RECALL
[F3] COPY
[F4] BULK
Mixing Voice Edit
Common Edit
[F1] GENERAL
[F2] OUTPUT
[F4] CTL SET
[F5] LFO
[F6] EFFECT
Element Edit
[F1] OSC
[F2] PITCH
[F3] FILTER
[F4] AMP
[F5] LFO
[F6] EQ
Mixing Voice Job
[F2] RECALL
[F3] COPY
[F5] DELETE
Supplementary Information
125
When the [EFFECT] lamp is turned on:
When the [ARP] lamp is turned on:
NOTE
Holding the [SHIFT] button and pressing the Knob Function 1 or 2 button will light the TONE1/EQ lamp.
Creating an Arpeggio
In addition to using the preset Arpeggios, you can also create your own original Arpeggio data. First, record a Phrase to
a Song or Pattern Track. Then, use the appropriate Song or Pattern Job function to convert the data (MIDI sequence
data) to Arpeggio data.
1 Record MIDI sequence data to a Song or Pattern.
2 Convert the MIDI sequence data (recorded to the Song or Pattern) to Arpeggio data.
Knob 5 CHO PRESET [SONG]/[PATTERN] Song/Pattern selection [MIXING] [EDIT]
[COMMON] [F6] EFFECT [SF4] CHORUS “Preset”
page 116
Knob 6 CHO SEND [SONG]/[PATTERN] Song/Pattern selection [MIXING] [F3] EF SEND
part selection “CHO SEND”
Knob 7 REV PRESET [SONG]/[PATTERN] Song/Pattern selection [MIXING] [EDIT]
[COMMON] [F6] EFFECT [SF4] CHORUS “Preset”
Knob 8 REV SEND [SONG]/[PATTERN] Song/Pattern selection [MIXING] [F3] EF SEND
part selection “REV SEND”
Knob 5 GATE TIME [SONG]/[PATTERN] Song/Pattern selection ARP [EDIT] [F5] PLAY FX
part selection “GateTimeRate” in the first page
page 83
Knob 6 OCT RANGE [SONG]/[PATTERN] Song/Pattern selection ARP [EDIT] [F5] PLAY FX
part selection “OctaveRange” in the first page
Knob 7 UNITMULTIPLY [SONG]/[PATTERN] Song/Pattern selection ARP [EDIT] [F5] PLAY FX
part selection “UnitMultiply” in the first page
Knob 8 TEMPO [SONG]/[PATTERN] Song/Pattern selection (Tempo)
Song or Pattern
Tra ck 1
Tra ck 2
Tra ck 3
Tra ck 4
Tra ck 5
Tra ck 6
Tra ck 7
Tra ck 8
Tra ck 9
Tra ck 10
Tra ck 11
Tra ck 12
Tra ck 13
Tra ck 14
Tra ck 15
Tra ck 16
Recording
Recording
Recording
Recording
Convert
Arpeggio
User Arpeggio 256
User Arpeggio 001
Tra ck 1
Tra ck 2
Tra ck 3
Tra ck 4
[SONG] [JOB] [F5] TRACK 07: Put Track To Arp
After setting the parameters as shown below. press the [ENTER] button
to execute Convert.
Yo u ca n re c o rd M I D I s e q ue n c e da t a fo r t h e
Arpeggio to any of the Tracks. After recording,
select four Tracks from all sixteen and convert
them to Arpeggio data.
Specify the destination
Arpeggio number.
Specify the source Song/Pattern
number and measure range.
Set the root note when the convert
type of any Track is set to “OrgNote.”
Select a convert
type by Track.
Specify the category of the
created Arpeggio.
Specify the Tracks of the source
Song or Pattern. Set unused
Tracks to “off.”