Filter
Top Products
PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Song Mode
Song Play
[F1] PLAY
[F2] GROOVE
[F3] TRACK
[F6] CHAIN
Song Record
Song Record Standby
[F1] SETUP
[F2] VOICE
[F3] ARP ED
[F5] CLICK
[F6] ALL TR
During Song Recording
[F1] SETUP
[F3] REST
[F4] TIE
[F5] DELETE
[F6] BAK DEL
Arpeggio Edit
[F1] COMMON
[F2] TYPE
[F3] MAIN
[F4] LIMIT
[F5] PLAY FX
[F6] OUT CH
Song Edit
[F1] CHANGE
[F2] VIEW FLT
[F4] TR SEL
[F5] INSERT
[F6] DELETE
Song Job
[F1] UNDO/REDO
[F2] NOTE
[F3] EVENT
[F4] MEAS
[F5] TRACK
[F6] SONG
Supplementary Information
89
04: Crescendo
This Job lets you create a crescendo or decrescendo over the specified range of notes. (Crescendo is a gradual
increase in volume, and decrescendo is a gradual decrease.)
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, all) and range of measures/beats/clocks over which the Job is applied.
VelocityRange
Determines the intensity of the crescendo or decrescendo. The velocity values of the notes in the specified range are
gradually increased or decreased starting at the first note in the range. The velocity of the last note in the range
becomes the original velocity of the note plus the Velocity Range value. If the resultant velocity is outside the 1 – 127
range, it is set to 1 or 127 accordingly. Settings greater than 0 produce a crescendo, and settings less than 0 produce a
decrescendo. A setting of 0 produces no effect.
Settings: -127 – +0 – +127
NOTE Executing this Job changes velocities of the note on events in the specified range to produce the crescendo/decrescendo. Note
that this Job cannot apply the crescendo/decrescendo to long sustained notes having a long gate time. If you wish to do this,
use the “Create Continuous Data” Job (page 92) with the Event Type set to “Control Change 11.”
05: Transpose
Transpose lets you change the key or pitch of the notes in the specified range.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, all) and range of measures/beats/clocks over which the Job is applied.
Note
Determines the range of note pitches over which the Job is applied. You can also set the note directly from the
keyboard, by holding down the [SF6] KBD button and pressing the desired key.
Settings: C -2 – G8
Transpose
Transposes notes in the specified range (in semitones). A setting of +12 transposes up one octave, while a setting of
-12 transposes down an octave. A setting of 0 produces no change.
Settings: -127 – +0 – +127
06: Glide
The Glide Job replaces all notes following the first note in the specified range with pitch bend data, producing smooth
glides from note to note. This is ideal for producing slide-guitar or string-bending effects.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, all) and range of measures/beats/clocks over which the Job is applied.
GlideTime
Determines the time of the glide. Higher values produce a longer glide between notes.
Settings: 000 – 100
PBRange (Pitch Bend Range)
Determines the maximum pitch bend range to be applied by the Glide Job (in semitones).
Settings: 01 – 24
NOTE Please note that the Song may not play back properly if you set the “PB Range” to a value different from the one set via the Voice
Edit mode. In order that the Song plays back properly, insert the MIDI event below to the corresponding Track in the Song Edit
display (page 84).
RPN [000-000] xxx (“xxx” represents the Pitch Bend value)
07: Create Roll
This Job creates a series of repeated notes (like a drum roll) in the specified range with the specified continuous
changes in clock step and velocity. This is ideal for creating fast staccato rolls and special stuttering effects.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16) and range of measures/beats/clocks over which the Job is applied.