Filter
Top Products
PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Song Mode
Song Play
[F1] PLAY
[F2] GROOVE
[F3] TRACK
[F6] CHAIN
Song Record
Song Record Standby
[F1] SETUP
[F2] VOICE
[F3] ARP ED
[F5] CLICK
[F6] ALL TR
During Song Recording
[F1] SETUP
[F3] REST
[F4] TIE
[F5] DELETE
[F6] BAK DEL
Arpeggio Edit
[F1] COMMON
[F2] TYPE
[F3] MAIN
[F4] LIMIT
[F5] PLAY FX
[F6] OUT CH
Song Edit
[F1] CHANGE
[F2] VIEW FLT
[F4] TR SEL
[F5] INSERT
[F6] DELETE
Song Job
[F1] UNDO/REDO
[F2] NOTE
[F3] EVENT
[F4] MEAS
[F5] TRACK
[F6] SONG
Supplementary Information
88
GateTime
Determines the gate time (the length of time a note sounds) of the even-numbered backbeat notes to enhance the
swing feel. When a triplet quantize value is used, the gate time of the last note of each triplet is adjusted. When the
quantize value is 8th note + 8th note triplet or 16th note + 16th note triplet, the gate time of the even-numbered 8th note
or 16th note beats will be adjusted. A setting of 100% leaves the original gate time unchanged. If an adjusted gate time
value is less than 1, the value is rounded off to 1.
Settings: 000% – 200%
02: Modify Velocity
This Job alters the velocity values of the specified range of notes, letting you selectively boost or cut the volume of those
notes. Velocity changes are calculated as follows:
Adjusted velocity = (original velocity x Rate) + Offset
If the result is 0 or less, the value is set to 1. If the result is higher than 127, the value is set to 127.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, all) and range of measures/beats/clocks over which the Job is applied.
SetAll
Sets the velocities of all target notes to the same fixed value (1 to 127). When set to “OFF” the Set All parameter has no
effect. When this is set to a value other than “off,” the Rate and Offset parameters are unavailable and appear as “***” on
the display.
Settings: off (0), 001 – 127
Rate
Determines the percentage by which the target notes will be shifted from their original velocities. Settings below 100%
reduce the velocities, and settings above 100% increase the velocities proportionately. A setting of 100 produces no
change. When the Set All parameter is not set to “off,” this parameter appears as “***” and cannot be changed.
Settings: 000% – 200%, ***
Offset
Adds a fixed value to the Rate-adjusted velocity values. Settings below 0 reduce the velocities, and settings above 0
increase the velocities. A setting of 0 produces no change. When the Set All parameter is not set to “off,” this parameter
appears as “***” and cannot be changed.
Settings: -127 – +0 – +127, ***
03: Modify Gate Time
This Job alters the gate times of the specified range of notes. Gate time changes are calculated as follows:
Adjusted gate time = (original gate time x Rate) + Offset
If the result is 0 or less, the value is rounded off to 1.
TR (Track) 001 : 1 : 000 – 999 : 4 : 479
Determines the Track (01 – 16, all) and range of measures/beats/clocks over which the Job is applied.
SetAll
Sets the gate times of all target notes to the same fixed value. When set to “OFF,” the Set All parameter has no effect.
When set to a value other than “off,” the Rate and Offset parameters are unavailable and appear as “***” on the display.
Settings: off (0), 0001 – 9999
Rate
Determines the percentage by which the gate time of the target notes will be changed. Settings below 100% shorten the
notes, and settings above 100% lengthen the notes proportionately. A setting of 100 produces no change. When the Set
All parameter is not set to “off,” this parameter appears as “***” and cannot be changed.
Settings: 000% – 200%, ***
Offset
Adds a fixed value to the Rate-adjusted gate time values. Settings below 0 shorten the gate time, and settings above 0
lengthen the gate time. A setting of 0 produces no change. When the Set All parameter is not set to “off,” this parameter
appears as “***” and cannot be changed.
Settings: -9999 – +0 – +9999, ***