Filter
Top Products
microKORG XL
50
DEST (Destination) ........................................................[PITCH…P.INT6]
Selects the parameter (destination) that will be controlled by the modula-
tion. For example if you select Tune, modulation will be applied to the over-
all pitch of the timbre.
INTENSTY (Patch Intensity)...................................................... [–63...63]
Specifies the depth of the effect produced by the modulation source.
With a setting of 0, there will be no modulation.
Setting example for “SOURCE” and “DEST”
SOURCE [1]
X
DEST [2]
PITCH The pitch of the entire timbre.
OSC2.TUNE The OSC2 page “TUNE”.
OSC1 C1 The OSC1 page “C1”. (J p. 36)
OSC1 LVL The MIXER page “OSC1 LVL”.
OSC2 LVL The MIXER page “OSC2 LVL”.
NOISE.LVL The MIXER page “NOISE.LVL”.
FILT1.BAL The FILTER1 page “TYPE BAL”.
CUTOFF1 The FILTER1 page “CUTOFF”.
RESO1 The FILTER1 page “RESO”.
CUTOFF2 The FILTER2 page “CUTOFF”.
WS DEPTH The DRIVE/WS page “DEPTH”.
LEVEL The AMP page “LEVEL”.
PANPOT The AMP page “PANPOT”.
LFO1.FREQ The LFO1 page “FREQ”.
LFO2.FREQ The LFO2 page “FREQ”.
PORTMNTO The PITCH page “PORTMNTO”.
OSC1 C2 The OSC1 page “C2”. (J p. 36)
EG1 INT1 The FILTER1 page “EG1 INT”.
KEY TRK1 The FILTER1 page “KEY TRK”.
RESO2 The FILTER2 page “RESO”.
EG1 INT2 The FILTER2 page “EG1 INT”.
KEY TRK2 The FILTER2 page “KEY TRK”.
ATTACK1 The EG1 page “ATTACK”.
DECAY1 The EG1 page “DECAY”.
SUSTAIN1 The EG1 page “SUSTAIN”.
RELEASE1 The EG1 page “RELEASE”.
ATTACK2 The EG2 page “ATTACK”.
DECAY2 The EG2 page “DECAY”.
SUSTAIN2 The EG2 page “SUSTAIN”.
RELEASE2 The EG2 page “RELEASE”.
ATTACK3 The EG3 page “ATTACK”.
DECAY3 The EG3 page “DECAY”.
SUSTAIN3 The EG3 page “SUSTAIN”.
RELEASE3 The EG3 page “RELEASE”.
P. INT1 The PATCH1 page “INTENSTY”.
P. INT2 The PATCH2 page “INTENSTY”.
P. I N T3 The PATCH3 page “INTENSTY”.
P. I N T4 The PATCH4 page “INTENSTY”.
P. I N T5 The PATCH5 page “INTENSTY”.
P. I N T6 The PATCH6 page “INTENSTY”.
EG1/EG2 XPI
TCH
The EG1 or EG2 will vary the pitch of the entire timbre over
time.
EG1/EG2 XPANPOT
The EG1 or EG2 will vary the pan over time. By setting two
patches to “MOD INT” settings with the opposite (+/–) value
you can create more complex panning.
LFO 1/LFO 2 XPITCH Vibrato will be applied at the LFO1 or LFO2 frequency.
LFO 1/LFO 2 XCUTOFF Wah will be applied at the LFO1 or LFO2 frequency.
LFO 1/LFO 2 XLEVEL Tremolo will be applied at the LFO1 or LFO2 frequency.
LFO 1/LFO 2 XPANPOT Auto pan will be applied at the LFO1 or LFO2 frequency.
VELOCITY XLEVEL Velocity (keyboard playing strength) will affect the volume.
KEY TRK XPANPOT
Keyboard position will gradually change the pan; lower
notes at the left, and higher notes at the right.
P. B E ND XPANPOT
PITCH wheel operations or pitch bend change will move
the sound between left and right.