Filter
Top Products
56
DT30-102025
Sure-Shot disc
No Picture
Default
Calibration #
33.00 g/rev
P102025
# of Holes
Diameter
Disc Thickness
0.2 Rev./min
6.4Rev./min
(6.4 RPM)
0.5 Rev./min
11.5 Rev./min
(11.5 RPM)
1.0 Rev./min
35.5 Rev./min
(35.5 RPM)
33.60 g/Rev.
1.3 g/Hole
0.87 lb/hr
0.40 kg/hr
2.18 lb/hr
0.99 kg/hr
4.36 lb/hr
1.98 kg/hr
27.94 lb/hr
12.67 kg/hr
49.77 lb/hr
22.57 kg/hr
154.90 lb/hr
70.29 kg/hr
42.75 g/Rev.
1.71 g/Hole
1.12 lb/hr
0.50 kg/h
2.77 lb/hr
1.26 kg/hr
5.55 lb/hr
2.52 kg/hr
35.56 lb/hr
16.12 kg/h
63.34 lb/hr
28.72 kg/hr
197.25 lb/hr
89.46 kg/hr
DT30 203012
Default
Calibration #
95.00 g/rev
203012
# of Holes
Diameter
Disc Thickness
0.2 Rev./min
6.4Rev./min
(6.4 RPM)
0.5 Rev./min
11.5 Rev./min
(11.5 RPM)
1.0 Rev./min
35.5 Rev./min
(35.5 RPM)
95.09 g/Rev.
7.92 g/Hole
2.51 lb/hr
1.14 kg/hr
6.28 lb/hr
2.85 kg/hr
12.50 lb/hr
5.70 kg/hr
80.50 lb/hr
36.50 kg/hr
143.28 lb/hr
65.00 kg/hr
446.54 lb/hr
202.50 kg/hr
118.72 g/Rev.
9.89 Hole
3.13 lb/hr
1.42 kg/h
7.80 lb/hr
3.54 kg/hr
15.65 lb/hr
7.10 kg/hr
100.53 lb/hr
45.60 kg/h
178.00 lb/hr
80.71 kg/hr
557.55 lb/hr
252.90 kg/hr
DT30 204010F
Default
Calibration #
150.00 g/rev
204010
# of Holes
Diameter
Disc Thickness
0.2 Rev./min
6.4Rev./min
(6.4 RPM)
0.5 Rev./min
11.5 Rev./min
(11.5 RPM)
1.0 Rev./min
35.5 Rev./min
(35.5 RPM)
151.15 g/Rev.
15.12 g/Hole
4.00 lb/hr
1.80 kg/hr
10.00 lb/hr
4.53 kg/hr
20.00 lb/hr
9.00 kg/hr
128.00 lb/hr
59.00 kg/hr
227.74 lb/hr
103.28 kg/hr
705.00 lb/hr
320.00kg/hr
188.72 g/Rev.
18.87 Hole
5.00 lb/hr
2.25 kg/h
12.43 lb/hr
5.64 kg/hr
25.00 lb/hr
11.30 kg/hr
160.00 lb/hr
72.50 kg/h
283.54 lb/hr
129.00 kg/hr
886.00 lb/hr
402.00 kg/hr
Note 1: This guide is to be used for general disc selection for Digital Dosing unit applications. All rates shown are continuous throughput and are
based on free-flowing materials. Consult factory for regrind, powder and all hard to flow materials.
Note 2: Maximum feeder disc revolutions in one screw recovery period (injection mode) is 9.5 revolutions. Use proper disc sizing for injection mode
applications to ensure proper dispense of material during the recovery cycle. Maximum dispense during a recovery cycle should not exceed 9.5
revolutions of the metering disc.