Filter
Top Products
EN-36
Editing a Tone
13: LFO Wah
This is a “wah” effect that can automatically affect the frequency
using an LFO.
Parameter Value Ranges:
1 :Input Level (0 to 127)
Adjusts the input level. The input signal can become distorted
when the level of the sound being input, the number of chords, or
the Resonance value is large. Adjust this parameter to eliminate
such distortion.
2 :Resonance (0 to 127)
Adjusts the strength of feedback
3 :Manual (0 to 127)
Adjusts the wah filter reference frequency.
4 :LFO Rate (0 to 127)
Adjusts the LFO rate.
5 :LFO Depth (0 to 127)
Adjusts the LFO depth.
6 :LFO Waveform (Sin, Tri, Random)
Selects the LFO waveform.
7 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
8 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
14: Auto Wah
This is a “wah” effect that can automatically shift the frequency in
accordance with the level of the input signal.
Parameter Value Ranges:
1 :Input Level (0 to 127)
Adjusts the input level. The input signal can become distorted
when the level of the sound being input, the number of chords, or
the Resonance value is large. Adjust this parameter to eliminate
such distortion.
2 :Resonance (0 to 127)
Adjusts the strength of feedback
3 :Manual (0 to 127)
Adjusts the wah filter reference frequency.
4 :Depth (–64 to 0 to +63)
Adjusts the depth of the wah in accordance with the level of the
input signal.
Setting a positive value causes the wah filter to open in direct
proportion with the size of the input signal, producing a bright
sound. Setting a negative value causes the wah filter to close in
direct proportion with the size of the input signal, producing a dark
sound.
5 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
6 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
15: Distortion
Distortion + Wah + Amp Simulator
Parameter Value Ranges:
1 :Dist Gain (0 to 127)
Adjusts the distortion input signal gain.
2 :Dist Level (0 to 127)
Adjusts the distortion output level.
3 :Dist Low (0 to 127)
Adjusts the distortion low-range gain.
4 :Dist High (0 to 127)
Adjusts the distortion high-range gain.
5 :Wah Depth (–64 to 0 to +63)
Adjusts the depth of the wah in accordance with the level of the
input signal.
6 :Wah Manual (0 to 127)
Adjusts the wah filter reference frequency.
7 :Routing (Dist, Wah, Wah-Dist, Dist-Wah)
Specifies the distortion and wah connection.
8 :Amp (Bypass, TCombo, FCombo, ACombo, BCombo, JCombo,
MStack, RStack, BassC, BassS)
Specifies the amp simulation type.
9 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
10:Dry Level (0 to 127)
Adjusts the level of the direct sound.
16: Pitch Shifter
This effect transforms the pitch of the input signal.
Parameter Value Ranges:
1 :Pitch (–24 to 0 to +24)
Adjusts the pitch shift amount in quarter tone steps.
2 :High Damp (0 to 127)
Adjusts the high-range damp. A smaller number increases
damping.
3 :Feedback (0 to 127)
Adjusts the feedback amount.
4 :Input Level (0 to 127)
Adjusts the input level.
5 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
6 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
17: Multi Chorus
This is a chorus effect with six different LFO phases.
Parameter Value Ranges:
1 :LFO Rate (0 to 127)
Adjusts the LFO rate.
2 :LFO Depth (0 to 127)
Adjusts the LFO depth.
3 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
4 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
18: Ring Modulator
Multiplies the input signal with an internal oscillator signal to create a
metallic sound.
Parameter Value Ranges:
1 :OSC frequency (0 to 127)
Sets the reference frequency of the internal oscillator.
2 :LFO Rate (0 to 127)
Adjusts the LFO rate.
3 :LFO Depth (0 to 127)
Adjusts the LFO depth.
4 :Tone (0 to 127)
Adjusts the timbre of the ring modulator input sound.
5 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
6 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
PX560-ES-1A.indd 38 2015/06/18 14:53:46