Filter
Top Products
SET SECURITY MODE
The Universal Receiver can be used with up to
15 rolling code transmitters or passwords in HIGH
security mode. Alternately, it can be used with up to 31
of any type transmitter in NORMAL security mode,
including any combination of rolling code, billion code,
or dip switch remotes.
The jumper must be set at the HIGH position for the
receiver to operate in HIGH security mode. It must be
set at NORMAL position to operate at the NORMAL
mode. (Figure 19)
When changing from NORMAL to HIGH security
mode, any previous transmitter codes must be erased.
Repeat Steps 2 and 3 in the Programming Section
below to reprogram the receiver for each remote
control transmitter in use.
The receiver is factory set at HIGH.
SET OUTPUT DURATION
For commercial applications, the receiver can be set
for either constant or momentary closure on the output
contacts. Use of constant closure is prohibited on
residential garage door openers because it overrides
the safety reversal devices.
With the jumper in the “M” (Momentary) position, the
contacts will close for 1/4 second regardless of the
length of radio transmission. With the jumper in “C”
(Constant) position, the contacts will stay closed as
long as the radio continues transmitting. (Figure 20)
The receiver is factory set at M.
PROGRAMMING THE REMOTE TO THE RECEIVER
1. Pry open the front panel of receiver case with a coin
or a screwdriver. Re-connect power to opener.
(Figure 21)
2. Press and release the “learn” button on the receiver.
The learn indicator light will glow steadily for 30 seconds.
3. Within 30 seconds, press and hold the button on the
hand-held remote that you wish to operate your
garage door.
The opener will now operate when the push button on
either the receiver or the remote control transmitter is
pressed.
Repeat Steps 2 and 3 for each remote control that will
be used to operate the garage door opener.
TO ERASE ALL REMOTE CONTROL CODES
Press and hold the “learn” button on the receiver panel
until the indicator light turns off (about 6 seconds). All
transmitter codes are now erased. Then follow the
steps above to reprogram each remote control.
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
ATTENTION
AVERTISSEMENT AVERTISSEMENT
AVERTISSEMENT
HIGH
SECURITY MODE
Security Mode
Terminals
Jumper
To prevent possible SERIOUS INJURY or DEATH, the use of
CONSTANT OPERATION on residential openers is PROHIBITED.
WARNING
CAUTION
WARNING
WARNING
ATTENTION
AVERTISSEMENT AVERTISSEMENT
AVERTISSEMENT
Output
Duration
Terminals
Jumper
M
CONSTANT
OPERATION
NORMAL
SECURITY MODE
Security Mode
Terminals
Jumper
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or
modifications of this receiver and/or transmitter are prohibited, except for changing the
code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Output
Duration
Terminals
Jumper
M
MOMENTARY
OPERATION
OPENING RECEIVER
Connect
Antenna
24V
12V
HIGH
NORM
C
P2
M
Learn Button
Indicator Light
Output Duration
Terminals
Security Mode
Power Supply
Jumper
OPEN RECEIVER
O. PROGRAMMING THE RADIO RECEIVER
Figure 19
Figure 20
Figure 21
Rev J Doc 01-20089 24 of 44