Filter
Top Products
En
4
About the AC adapter
Safety instructions
To ensure your personal safety and to maximize the full operating potential of your
unit, read and follow these safety instructions.
Read & Retain Instructions
Read all operating and user information provided with this product.
Cleaning
Use a damp cloth to clean the exterior housing. Avoid using any fluids including
liquid, aerosol or alcohol-based cleaning products.
Water or Moisture
Avoid operating or locating this product near water or other sources of fluid.
Accessories
Do not place this product on an unstable cart, stand, or table. The product may fall
and be seriously damaged.
Ventilation
Do not block or cover this product in use. This unit should not be placed in a built-in
installation unless properly ventilated.
Environment
Avoid placing this product in a location with exposure to large quantities of dust,
high temperatures, high humidity, or subject to excessive vibrations or shocks.
Power Sources
Operate this product only from the recommended power sources. If you are unsure
of the power source, consult an authorized Pioneer representative.
Power-Cord Protection
When unplugging the unit, pull on the plug – not on the cord. Do not handle the
cord or plug with wet hands; doing so could cause an electric short or shock. Do not
allow anything to pinch or rest on the power cord and do not place in a walkway.
Power
Turn OFF the system before installing this or any other hardware device.
Overloading
Avoid connecting too many devices to a single wall socket or power source as this
can cause fires or short circuits.
Object & Liquid Entry
Never push inappropriate objects in to the device. Avoid spilling any liquids in to or
on the outside of the drive.
Servicing
Opening or removing the cover exposes you to possible electrical shock or other
danger. Contact a Pioneer authorized service representative for repairing this prod-
uct (refer to the enclosed Service & Support Card).
Damage Requiring Service
Unplug the unit and refer servicing to qualified service personnel in the following
situations:
%
When the power cord, plug, or chassis is damaged.
% If liquid has been spilled, or objects have fallen into the product.
% If the product has been exposed to rain or water.
%
If the product does not operate normally when the operating instructions are
followed. Adjust only those controls that are covered by the operating instructions.
Improper adjustment of other controls may result in damage and can require
extensive work by a qualified technician to restore the unit to its normal operation.
% When the product exhibits a distinct change in performance – this indicates a
need for service.
Check that there are no irregularities with the AC adapter or power plug, then insert
the power plug into the specified position of the AC adapter using the specified pro-
cedure until a click is heard. For details, see Mounting the power plug on page
4 .
If there are irregularities with the AC adapter or power plug, ask your nearest
Pioneer authorized service center or your dealer to carry out repair work.
Cautions on use
! Do not use this unit with a coin, paper clip or other metal object stuck between
the AC adapter and power plug. Doing so could cause a short circuit, leading to
fire or electric shock.
! When mounting the AC adapter on a wall outlet, make sure there is no space
between the AC adapter and the wall outlet. Faulty contact or a coin, paper clip
or other metal object getting stuck in the space could cause a short circuit, lead-
ing to fire or electric shock.
Coin, paper clip or other metal object
Top
Side
! The power plug could come detached from the AC adapter and remain in the
power outlet if someone trips on the AC adapter’s power cord or if something
hits the AC adapter. If this happens, remove the power plug remaining in the
outlet with dry hands, holding it as shown on the diagram below and without
touching metal parts. Do not use any tools to remove it.
Do not touch.
Mounting the power plug
Slide the power plug along the guide rails in the AC adapter
unit as shown on the diagram below, then press in until a click
is heard.
Removing the power plug
While pressing the [PUSH] button on the AC adapter unit,
slide the power plug away from the adapter as shown on the
diagram below to remove it.
Once the power plug is mounted, there is no need to remove it.