Filter
Top Products
PERF SONG PATTERN MIX MASTER REMOTE UTILITY
QUICK SET
FILEVOICE
MOXF6/MOXF8 Reference Manual
Performance Mode
Performance Play
[F1] PLAY
[F2] VOICE
[F3] PORTA
[F4] EG
[F5] ARP ED
[F6] EFFECT
Arpeggio Edit
[F1] COMMON
[F2] TYPE
[F3] MAIN
[F4] LIMIT
[F5] PLAY FX
[F6] OUT CH
Performance Edit
Common Edit
[F1] GENERAL
[F2] OUT/MFX
[F3] MEQ
[F4] USB I/O
[F5] A/D IN
[F6] EFFECT
Part Edit
[F1] VOICE
[F2] OUTPUT
[F3] EQ
[F4] TONE
[F5] RCV SW
Performance Job
[F1] INIT
[F2] RECALL
[F3] COPY
[F4] BULK
Performance Record
[F1] SETUP
[F2] REC TR
[F3] OTHER
[F5] CLICK
[F6] INFO
Supplementary Information
57
Pressing this button calls up the Arpeggio Edit display of the Performance mode.
Pressing this button calls up the EFFECT display (page 63) of Performance Common Edit.
Arpeggio Edit
This display contains the basic settings for Arpeggio playback, including Type and Tempo in the Performance mode.
The MOXF6/MOXF8 has four arpeggiators. In the Performance mode, the different Arpeggio types can be assigned to
up to four parts, and the up to four arpeggio types can be simultaneously played. The parameters are the same as in
the Voice mode (page 27), except for the following parameters.
Tempo (Arpeggio Tempo)
Determines the tempo for the Arpeggio.
Settings: 5 – 300
NOTE If you are using this instrument with an external sequencer, DAW software, or MIDI device, and you want to synchronize it with
that device, set the “MIDI Sync” parameter in the MIDI display of the Utility mode (page 148) to “external” or “auto.” When “MIDI
Sync” is set to “auto” (only when MIDI clock is transmitted continuously) or “external,” the Tempo parameter here indicates
“external” and cannot be changed.
NOTE This parameter can be set also by holding the [SHIFT] button and pressing the [ENTER] button several times repeatedly at the
desired tempo. This function is referred to as “Tap Tempo.”
Switch (Common Switch)
Determines whether Arpeggio is on or off for all Parts. This setting is applied to the ARP [ON/OFF] button on the panel.
Settings: off, on
SyncQtzValue (Sync Quantize Value)
Determines the actual timing at which the next Arpeggio playback starts when you trigger it while the Arpeggio of a
certain Part is played back. When set to “off,” the next Arpeggio starts as soon as you trigger it. The number shown at
right of each value indicates the resolution of the 1/4 note in clocks.
Settings: off, 2 60 (32nd note), 63 80 (16th note triplet), 6 120 (16th note), 83 160 (8th note triplet), 8 240 (8th note), 43 320 (1/4
note triplet), 4 480 (1/4 note)
QtzStrength (Quantize Strength)
Determines the offset value for “QtzStrength” in the [F5] PLAY FX display. This parameter is applied to all parts.
Settings: -100 – +0 – +100
VelocityRate
Determines the offset value for “VelocityRate” in the [F5] PLAY FX display. This parameter is applied to all parts.
Settings: -100 – +0 – +100
GateTimeRate
Determines the offset value for “GateTimeRate” in the [F5] PLAY FX display. This parameter is applied to all parts.
Settings: -100 – +0 – +100
Swing
Determines the offset value for “Swing” in the [F5] PLAY FX display. This parameter is applied to all parts.
Settings: -120 – +0 – +120
[F5] ARP ED (Arpeggio Edit)
[F6] EFFECT
Operation
[PERFORM] Performance selection [F5] ARP ED
Performance mode ARP [EDIT]
[F1] COMMON
Knob
Knob