LG - Life's Good STB-3000 Manual

next previous

206-4272

Reference: Using the STB’s Zoning Features (Cont.)

Using the Wi-Fi Zoning Feature with Cloning Conguration

Alocation-specicWi-Ficonguration/.tlxlemaybesaved(Learned)fromanindividualSTB as part of a

Master STB Setup and then be used during Teaching. First, the wireless network (i.e., the access point login

data)mustbeconguredintheMasterSTB’s IP Environment Menu (see “ConguringaWi-FiNetwork

Connection” on page 58). Then, a Wi-Fi Zone # must be set in the Master STB (see “Set the TV Zone #

and/or Wi-Fi Zone # in the STB” below). If desired, a TV Zone # may also be set in the Master STB.

For example, if the Wi-Fi Zone # is set to 4 and the TV Zone # is set to 5 before Learning is initiated, after

Learning is completed, the Master STB’sInstallerMenuprolewillbesavedwiththeZone5assignment,

andwithinthatInstallerMenuprole,theaccesspointlogindataforwirelessnetworking(i.e., SSID, security

type, and security key) willbesavedwithaWi-FiZone4assignment.InordertoconguretheTargetSTBs

withtheproperInstallerMenuproleandaccesspointlogindata,youmustsetboththeTVZone#andthe

Wi-Fi Zone # in the Target STBs accordingly before transferring (Teaching) the Master STB Setup. See “Set

the TV Zone # and/or Wi-Fi Zone # in the STB” below. Also, see “Cloning Procedures” on pages 42 to 47 for

additional information on the cloning processes. If the Wi-Fi Zone # in the STB is set to 0 (default), the STB

willnotobtainaccesspointlogindatafromtheInstallerMenuprolewithwhichitisconguredunless the

prolecontainstheglobalWi-FiZone100.Similarly,anySTBthatdoesnotnditsmatchingWi-FiZone#

intheTLXle,butthatdoesndtheglobalWi-FiZone100,willbeconguredwiththeglobalaccesspoint

Set the TV Zone # and/or Wi-Fi Zone # in the STB

You can set the TV Zone # and/or the Wi-Fi Zone # in the EZ-Manager Wizard (see “EZ-Manager Wizard”

on pages 15 to 24) or, if the STB is in Pass-through Mode, via the STB’s setup menus as described below.

Note that the following procedure can only be performed while the STB is in Pass-through Mode. You will

also be able to specify a Label (North, South, East, West) and Room Number for this STB, if desired.

1. Turn ON the STB/display panel.

2. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the

General menu option. Then, press OK.

3. In the General Menu, use the Up/Down arrow keys to select Room Info, and then press OK.

4. IntheRoomInfoscreen,completetheappropriateeldsasdescribedbelow.UsetheUp/Down arrow

keysontheInstallerRemotetonavigatebetweeneachoftheelds.

• Wi-FiZone:EnablesyoutosetaWi-FiZone#sothattheSTBcanbeconguredwithaparticular

access point’s login data for wireless networking. Login data (i.e., SSID, security type, and security

key)maybeprovidedinaTLXletobeusedforconguration.

To assign a Wi-Fi Zone, select/highlight the Wi-Fi ZoneeldandpressOK. Then, use the Left/Right

arrow keys to specify the desired Wi-Fi Zone # (1–99). Press OKwhenyouarenished.

• TV Zone: Enables you to set a TV Zone # so that the STBcanbeconguredwithInstallerMenuand/or

STB Setup Menu settings intended only for the assigned Zone. The Installer Menu and/or STB Setup

MenusettingsmaybeprovidedinaTLXletobeusedforconguration.IftheSTBisbeingcongured

for FTG Mode, the TV Zone # setting also allows the STB to omit channels that have been restricted in

the FTG Channel Map.

To change the TV Zone, select/highlight the TV ZoneeldandpressOK. Then, use the Left/Right

arrow keys to specify the desired TV Zone # (0–8). Press OKwhenyouarenished.

(Continued on next page)