Filter
Top Products
5
LOCATION
Locate the steam generator
horizontally on the rest plate of
your ironing board (if large
enough) or on a heat resistant
stand at the same height as
your ironing board or below it.
Always ensure the generator is
on a firm surface when ironing.
WARNING: Do not use the
product on a surface which
could be damaged by heat or
steam such as a worktop or
a polished wood surface.
If in doubt, contact Morphy
Richards.
BEFORE USE
Remove any protective sticker
from the soleplate and the base
unit, if any.
Unwind and straighten the
power cord ‡ and supply cord
fl.
Slide out the water tank · and
fill (see filling instructions).
When ironing with the iron
temperature set at 2-dot
setting, the steam output
should be set at the lower end
of the steam range (on certain
models only).
Textiles and clothes are
supposed to carry ironing
instructions. If they don’t, you
should follow the fabric guide
on page 3, but be sure to test
the temperature by ironing the
hem of the garment or similar
area first.
If you turn the control dial
down from a hot setting to a
cooler setting, wait until the
iron temperature has stabilised
before you continue ironing.
FILLING
1 Place the steam generator on a
stable ironing board or table,
with the iron resting on its
stand.
2 Release the detachable water
tank by operating the tank
release knob „.
3 Slide the tank outward.
4 Fill the tank to the ‘fill to here’
line with clean tap water A.
IN HARD WATER AREAS,
THE USE OF DISTILLED OR
DEMINERALISED WATER
IS RECOMMENDED.
Never use battery topping up
fluid or water containing any
substances like starch or
sugar, or defrosted water
from a refrigerator.
5 Re-position the water tank on
the base unit and push
securely into place. Please
make sure the tank is secure
B.
6 Always pour out any remaining
water after use.
Re-filling ‘in use’
1 The low water indicator light Ê
will flash and a beep sound will
be heard. This is a warning to
stop ironing and fill the tank.
Ironing can continue for a short
period, then the generator will
shut down until the tank is
refilled.
2 Refilling can be done whilst the
appliance is in operation. It is
not necessary to wait for the
appliance to cool down.
3 Unlock the tank using the tank
release knob „. Slide out the
water tank and fill (see filling
instructions).
4 Alternatively, you can re-fill the
tank in ‘situ’ through the filler
‚.
Steam ironing
1 Connect the appliance to a
suitable mains outlet. Press the
power ‘ON’ button Á which
will glow red.
ALL MODELS
After a few minutes, the light
changes to green - indicating
the boiler is ready to generate
steam.
Check the iron temperature
indicator light ¤ has switched
off, indicating the iron is ready
to use.
MODELS WITH VARIABLE
STEAM
This model automatically
selects the middle steam
setting as the default setting.
To select a different steam
setting, press the steam button
Î to select the desired steam
level.
2 Turn the temperature dial › on
the iron in a clockwise
direction, select
dot-1, dot-2 or dot-3 according
to the recommendation of the
garment label.
3 The iron’s temperature indicator
light ¤ goes off when the
required temperature is
reached.
4 Depress the steam button ⁄
for 1 minute to clear the system
of air (first time use only). This
will be accompanied by a
clicking noise which is quite
normal.
5 Begin first time ironing with an
old towel. Note: If you press
the steam button before the
steam generator reaches its
required temperature, a
warning double beep will
sound.
6 The appliance is ready to use.
A
B
UK
Helpline 0870 060 2614 Replacement Parts 0870 157 6645 Ireland Helpline 1800 409119
For details of other Morphy Richards products, please see our website:
RN42288MUK Rev7:RN42288MUK Rev7 04/11/2009 10:28 Page 5