Filter
Top Products
9
Installation Instructions for Cosco
®
Designer/Opus 35
The Double Snap-N-Go
®
will accommodate the Cosco
®
Designer/Opus 35
Infant Car Seat. Please follow these instructions for proper installation of
the Cosco
®
.
Front Seat:
1. Remove (unscrew) Crossbars A1, C and D from the Double Snap-N-Go
®
frame. Leave Crossbar B1 in hole labeled #4. Remove the Car Seat Straps
from the Double Snap-N-Go
®
frame. Retain the screws you remove.
2. Attach Crossbar B1 (removed from the rear section of the Double Snap-
N-Go
®
frame), so that the bent section faces down, to the Double Snap-N-
Go
®
frame using the two holes labeled #5. Use the two screws that you
removed in step 1. Please see gure 1.
3. Attach both Car Seat Straps to the Double Snap-N-Go
®
frame using the
two holes labeled #3. Use the two screws that you removed in step 1.
Please see gure 1.
Rear Seat
1. Remove (unscrew) Crossbars A2 and B1 from the Double Snap-N-Go
®
frame. Remove the Car Seat Straps from the Double Snap-N-Go
®
frame.
Retain the screws you remove.
2. Attach Crossbar C (removed from the front section of the Double Snap-N-
Go
®
frame) to the Double Snap-N-Go
®
frame using the two holes labeled
#4. Use the two screws that you removed in step 1. Please see gure 2.
3. Attach both Car Seat Straps to the Double Snap-N-Go
®
frame using the
two holes labeled #1. Use the two screws that you removed in step 1.
Please see gure 2.
Insertion of the Cosco
®
Designer/Opus 35 Infant Car Seat
1. With one hand grasp the car seat handle (in its upright, carrying position)
and with your other hand squeeze the handle on the back of the car seat
and gently place the seat, so that the baby faces the rear, onto the Double
Snap-N-Go
®
so that the rear small grooves on the seat bottom hook over
Crossbar B1 for the front position or Crossbar C for the rear position.
Release the handle and check that the seat locked onto the bar. See
Figure 3. FOR SAFE OPERATION, IT IS VERY IMPORTANT
THAT THE REAR LATCHES OF THE SEAT LOCK SECURELY
ONTO THE CROSSBAR.
2. Feed the Car Seat Straps through the slots found on the rear of the Car
Seat shell as shown in gure 4. Buckle the two straps together. The rst
time your do this, you will need to adjust the length of the strap for a tight
t around the car seat. Please see gure 4.
3. Test for secure installation by moving the car seat in all directions. The
car seat should be securely attached to the Double Snap-N-Go
®
.
Removal of the Cosco
®
Designer/Opus 35 Infant Car Seat
1. Unlock the Car Seat Strap and remove.
2. With one hand, grasp the car seat handle (in its upright, carrying position)
and with your other hand squeeze the handle on the back of the car and
lift the car seat upward from the Double Snap-N-Go
®
. See Figure 5.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Bar B1
Bar B2
Bar C
Bar B1
down
Hole #3
Hole #4
Hole #5
Hole #4
Hole #3
Hole #1
Strap
Strap
Cosco
®
and Designer/Opus 35 are the trademarks of their owners. They are
not associated with Baby Trend and no approval or endorsement is implied.