Filter
Top Products
Installation Instructions for Century
®
Vante
The Double Snap-N-Go
®
will accommodate the Century
®
Vante Infant Car
Seat. Please follow the following instructions for proper installation of the
Vante.
Front Seat:
1. Remove (unscrew) Crossbars A1, B1, C and D from the Double Snap-N-
Go
®
frame. Retain the screws you remove.
2. Attach Crossbar C on top of Crossbar B1, with the bent side of B1 facing
downward, to the Double Snap-N-Go
®
frame using the two holes labeled
#2. Use the two long screws provided separately. Please see gure 1.
3. Attach Crossbar B1, taken from the rear of the Double Snap-N-Go
®
frame,
to the Double Snap-N-Go
®
frame using the two holes labeled #7. Use the
two screws that you removed in step 1. Please see gure 1.
Rear Seat:
1. Remove (unscrew) Crossbars A2, B2, and B1 from the Double Snap-N-
Go
®
frame. Remove the Car Seat Straps from the Double Snap-N-Go
®
frame. Retain the screws you remove.
2. Attach Crossbar D, removed in the Front Seat step 1 above, to the Double
Snap-N-Go
®
frame using the two holes labeled #5. Use the two screws
that you removed in step 1. Please see gure 2.
3. Attach both Car Seat Straps to the Double Snap-N-Go
®
frame using the
two holes labeled #4. Use the two screws that you removed in step 1.
Please see gure 2.
Insertion of the Century
®
Vante Infant Car Seat
1. With one hand grasp the car seat handle (in its upright, carrying position)
and gently place the seat, so that the baby faces the rear of the Double
Snap-N-Go
®
, onto the Double Snap-N-Go
®
so that the large groove on the
seat bottom, nearest the head-end of the seat, hooks over the Crossbar C/
B1 combination in the front position or hooks over the top section of the
Double Snap-N-Go
®
frame in the rear position. Check that the seat locked
onto the Crossbar or frame. See Figure 3. FOR SAFE OPERATION,
IT IS VERY IMPORTANT THAT THE SEAT LOCK SECURELY
ONTO THE CROSSBAR OR FRAME.
2. Feed the Car Seat Straps through the auto belt slots on the infant car seat as
shown in Figure 4 and snap the two buckles together. The rst time your
do this, you will need to adjust the length of the strap for a tight t around
the car seat. FOR SAFE OPERATION, IT IS VERY IMPORTANT
THAT THE CAR SEAT STRAP IS ALWAYS TIGHTLY FASTENED
OVER THE CAR SEAT.
3. Test for secure installation by moving the car seat in all directions. The
car seat should be securely attached to the Double Snap-N-Go
®
.
Removal of the Century
®
Vante Infant Car Seat
1. Unlock the Car Seat Strap and remove from over the infant car seat.
2. With one hand, grasp the car seat handle (in its upright, carrying position)
and with your other hand squeeze the handle on the back of the car seat
and lift the car seat upward from the Double Snap-N-Go
®
frame. See
Figure 5.
Bar C
Bar B1
Hole #7
Hole #2
Hole #6
Bar B1
Strap
Bar D
Hole #4
Hole #5
Strap
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
8
2
Century
®
and Vante are the trademarks of their owners. They are not
associated with Baby Trend and no approval or endorsement is implied.