Filter
Top Products
Snap all 4 snaps back down on the seat pad.
36• To fasten the harness, check that the shoulder
straps are properly inserted in the waist strap,
then click together the buckle of the waist strap
and the leg strap. To unfasten the harness, press
on the side of the buckle while pulling the waist
strap upwards.
The new safety belt is easier to wear, thanks to
the “snap open and shut” system. Before attaching
the safety belt, attach the small buckle to the
backrest by inserting the tab into the special
holder, as shown in the figure. Next, fasten the
safety belt on your child, and then detach the
belt from the backrest to allow the child more
freedom of movement. The small buckle should
be placed below the child’s shoulders. To tighten
the waist strap, pull on both sides in the direction
of the arrow (fig_6). To loosen it do the opposite.
The waist strap can be tightened as far as the
safety lock.
FOLDING THE STROLLER/CARRIAGE
• Close the hood, if attached:
• Move the Skate-seat down to the lowest position.
37• If the Skate-seat is attached to the Skate chassis
facing parents, first pull out the safety trigger
(1) and simultaneously recline the Skate-seat
by pulling up the handle behind the backrest
(2), then align the seat to the Skate handlebar
assembly (3).
38• If the Skate-seat is attached to the Skate chassis
so that the child can see what's ahead, recline the
Skate-seat by pulling up the handle behind the
backrest and align the seat to the Skate chassis.
39• To close the Skate chassis when it is fully
reclined, move the telescopic handlebar if
extended to the lowest position. Press the
folding pedal with a foot. Next pull the left
trigger and then the right trigger.
40• now you will lower the handlebar down and
rotate the handle grip down.
41• take out the locking levers and attach them to
the side pins.
42• It stands on its own with the large wheels
closest to the ground.
• To fold the Skate chassis in a compact way,
remove the Skate-seat and wheels.
CARRYING THE STROLLER/CARRIAGE
43• There are two carrying modes. You can carry the
carriage/stroller either holding the handle under
the basket or as a trolley; the handlebar must
be long and straight and the front wheels in the
non-swivel position.
Skate chassis + primo viaggio
car seat
• Standard adapters allow to attach the Skate
chassis to the car seat group 0+ "Primo Viaggio
SIP" or "Primo Viaggio tri-fix" Peg Perego.
44• Before attaching the adapters, check that the
two locking systems of the Skate chassis are in
the central and upright position.
• If you are standing behind the stroller pushing it,
DX is the right side and SX is the left side.
45• To attach the adapters, place the locking
systems in the holes of the Skate chassis.
46• To attach the car seat to the Skate chassis, place
the seat facing parents next to the adapters and
push it down so it attaches to the 2 adapter pins
in the middle notches on the bottom of the car
seat, The car seat can be adjusted to 3 height
positions.
• To release the car seat from the Skate chassis,
pull up the lever on the backrest of the car seat.
47• To remove the adapters, press the inside button
and pull them upward.
accessory range
48• Skate bag: Multi-function bag, can be attached
to the handlebar (A) and basket (B). Contains a
nappy change mat and a removable thermal
bottle holder.
removable lining
REMOVE THE OUTER LINING
• Remove the hood, cover and bumper bar if
attached, and fully lower the backrest and
legrest.
49• Unfasten the 2 buttons near the center of the
unit on the inner padding from the outer lining.
• Unbutton the outer lining on both sides of the
top from inside the Skate-seat.
50• Open the 3 zippers on the outer lining (1 at the
bottom and 2 at the top of the Skate-seat).
51• On the outside of the Skate seat, unfasten the
two elastic strings of the outer lining from the T
shaped pins on both sides of the seat.
52• From inside the Skate-seat, first remove the
upper part and then the side parts of the inner
lining from the side pins.
53• Take out the outer lining from the Skate-seat,
together with the backrest adjusting strap.
54• Move down the outer lining.
55• Unscrew the 6 pins from the bottom of the
Skate-seat.
TAKE OUT THE INNER PADDING
• To take out only the inner padding, remove the
outer lining without unscrewing the pins.
• If the safety belts are out, put them in the
padding under the seat.
56• Take the 2 fixing tabs of the inner padding out
of the Skate-seat.
57• Take the 4 fixing tabs of the inner padding out
of the sides of the Skate-seat.
58• Take the backing of the Skate-seat out of the
pocket behind the inner padding.
cleaning & maintenance
• This product requires some maintenance.
Cleaning and maintenance operations must be
carried out only by adults.
• You are recommended to keep clear all the