Filter
Top Products
Parts List:
Description Qty.
F
rame assembly with seat,
canopy, and wrist strap
rame assembly with seat,
canopy, and wrist strap
rame assembly with seat,
1
Front Wheel 1
Parent Console
(not on all models)
1
Under-seat Basket
(not on all models)
1
Rear Wheels 2
Front Fender 1
#8 – 11.2
"
Phillips head screws 4
Tools Req
uired:
Phillips screw driver, adjustable wrench.
Stroller Assembly Instructions
Unfold Stroller: Remove from carton and remove any packaging materials that
may be holding the frame in closed position. Grasp frame handle and open.
Unfold Stroller: Remove from carton and remove any packaging materials that
may be holding the frame in closed position. Grasp frame handle and open.
Unfold Stroller: Remove from carton and remove any packaging materials that
Lock both plastic latches, on sides, onto the lower frame, insert locking pin into
may be holding the frame in closed position. Grasp frame handle and open.
Lock both plastic latches, on sides, onto the lower frame, insert locking pin into
may be holding the frame in closed position. Grasp frame handle and open.
hole in latch and frame, lock the pin in place by slipping the wire loop over
Lock both plastic latches, on sides, onto the lower frame, insert locking pin into
hole in latch and frame, lock the pin in place by slipping the wire loop over
Lock both plastic latches, on sides, onto the lower frame, insert locking pin into
the end of the lock pin. {see Figure 1.A}
hole in latch and frame, lock the pin in place by slipping the wire loop over
the end of the lock pin. {see Figure 1.A}
hole in latch and frame, lock the pin in place by slipping the wire loop over
Rear Wheel Assemb
ly
Grasp rear wheel in on
e hand, slide wheel’s axle into hole in rear of frame.
Push up on the axle release lever so that the wheel is fully inserted. Pull the
Grasp rear wheel in on
Push up on the axle release lever so that the wheel is fully inserted. Pull the
Grasp rear wheel in on
wheel fi rmly, the wheel should not come off if fully inserted/locked. Repeat for
Push up on the axle release lever so that the wheel is fully inserted. Pull the
wheel fi rmly, the wheel should not come off if fully inserted/locked. Repeat for
Push up on the axle release lever so that the wheel is fully inserted. Pull the
other side. To release wheel push up on axle release lever and pull off wheel.
wheel fi rmly, the wheel should not come off if fully inserted/locked. Repeat for
other side. To release wheel push up on axle release lever and pull off wheel.
wheel fi rmly, the wheel should not come off if fully inserted/locked. Repeat for
Front Wheel Assembly
Tip stroller back so that the handlebar is down on the ground and the front fork
is up. Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever
Tip stroller back so that the handlebar is down on the ground and the front fork
is up. Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever
Tip stroller back so that the handlebar is down on the ground and the front fork
on the front wheel far enough to allow the axle to slide into the front fork. With
is up. Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever
on the front wheel far enough to allow the axle to slide into the front fork. With
is up. Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever
wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight,
then fl ip wheel’s Q/R lever backward to the closed position to lock wheel in
wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight,
then fl ip wheel’s Q/R lever backward to the closed position to lock wheel in
wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight,
place. Note this step may require minor adjustment until the Q/R lever fl ips back
then fl ip wheel’s Q/R lever backward to the closed position to lock wheel in
place. Note this step may require minor adjustment until the Q/R lever fl ips back
then fl ip wheel’s Q/R lever backward to the closed position to lock wheel in
with fi rm pressure. Pull outward on wheel to ensure it is locked in place.
place. Note this step may require minor adjustment until the Q/R lever fl ips back
with fi rm pressure. Pull outward on wheel to ensure it is locked in place.
place. Note this step may require minor adjustment until the Q/R lever fl ips back
Caution:
The interior jam nuts are factory installed and do not need adjustment.
Close the front caliper brake by lowering the Q/R lever. Spin the front wheel
to make sure the brake pads do not rub and are properly aligned to the rim. If
Close the front caliper brake by lowering the Q/R lever. Spin the front wheel
to make sure the brake pads do not rub and are properly aligned to the rim. If
Close the front caliper brake by lowering the Q/R lever. Spin the front wheel
brake pad alignment is off, loosen brake pad nut with an adjustable wrench,
to make sure the brake pads do not rub and are properly aligned to the rim. If
brake pad alignment is off, loosen brake pad nut with an adjustable wrench,
to make sure the brake pads do not rub and are properly aligned to the rim. If
align brake pad and retighten nut while holding brake pad in place.
Caution:
Always be sure to reengage the brake by rotating the Q/R lever for-
ward (toward the front wheel) before using the stroller.
Always be sure to reengage the brake by rotating the Q/R lever for-
ward (toward the front wheel) before using the stroller.
Always be sure to reengage the brake by rotating the Q/R lever for-
IMPORTANT
If you notice that the stroller steers to one direction you may need to adjust the
front wheel to align it. To do so loosen the front axle Q/R lever, points the front
If you notice that the stroller steers to one direction you may need to adjust the
front wheel to align it. To do so loosen the front axle Q/R lever, points the front
If you notice that the stroller steers to one direction you may need to adjust the
wheel in the opposite direction the stroller is veering, and retighten the Q/R lever.
If you need help making this adjustment, please call our Customer Service
wheel in the opposite direction the stroller is veering, and retighten the Q/R lever.
If you need help making this adjustment, please call our Customer Service
wheel in the opposite direction the stroller is veering, and retighten the Q/R lever.
department for assistance.
If you need help making this adjustment, please call our Customer Service
department for assistance.
If you need help making this adjustment, please call our Customer Service
axle release lever
Rear Wheel Assemb
ly -
{Figure 1.b}
quick
-release
-release
lever
quick
lever
quick
(open
position)
Front Wheel Assemb
ly
Operating Instructions
Run Around
™
& Run Around
™
LTD 11-KS107, 11-KS186, 11-KS187...page 2