Filter
Top Products
CCH00701:09/00 JCHE p65
DOUBLE D ROPSIDE C RIB
child craftchild craft
child craftchild craft
child craft
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: 812-883-1819 - http://www.childcraftind.com
ASSEMBLY DIRECTIONS AND PARTS LIST
ΦREAD ALL INSTRUCTIONS WITH CARE BEFORE STARTING THE ASSEMBLY PROCEDURE.
ΦΦ
ΦΦ
ΦYOU WILL NEED A #2 PHILLIPS SCREWDRIVER, A SLOTTED SCREWDRIVER AND A HAMMER.
PARTS E NCLOSED IN H ARDWARE B AG ( NOTED WHEN SHOWN ACTUAL SIZE)
(18) Slotted/Phillips
Wood Screws
EE
EE
E
(12) Slotted/Phillips
Machine Screws
AA
AA
A
(actual size)
BB
BB
B
(4) Spring Hangers
CC
CC
C
(4) Gate Shoes
DD
DD
D
(2)
Moulded
plastic
backers
(2)
4-Position
Spring
Hanger
Brackets
(actual size)
FF
FF
F
(4) Compression
Springs
GG
GG
G
(4) Bumper
Springs
HH
HH
H
(4) Casters
(style may vary)
II
II
I
(2) Angle
Brackets
PARTS I NCLUDED IN C ARTON
OO
OO
O
(1) Footboard
NN
NN
N
(1) Headboard
PP
PP
P &
QQ
QQ
Q
(2) Crib sides
(Dropsides)
RR
RR
R
(1) Spring
JJ
JJ
J
(2) Stabilizer Bars
KK
KK
K
(4) Crib Rods
PREPARATION
Carefully remove and lay out all hardware and parts. Remove wires securing the (2) Stabilizer Bars
JJ
JJ
J and the (4) Crib Rods
KK
KK
K to Crib Spring
RR
RR
R. Check
quantities and match to the three Parts Lists above. If any part is missing or broken contact your dealer or Child Craft (P.O. Box 444, Salem, IN 47167-
0444 USA (ph# 812/883-3111), service@childcraftind.com for a replacement part or instructional literature. Before making this contact, identify your crib.
A model identification number is stamped on the underneath side of the bottom rail of either a crib end
NN
NN
N/
OO
OO
O or a crib side
PP
PP
P/
QQ
QQ
Q. Record the model
Identification Number now: # ______________________. Include this number with a request for a part or instructional literature. DO NOT SUBSTITUTE
PARTS!
Note the two piece assembly of 4-Position Spring Hanger Brackets
DD
DD
D. Before
attachment to crib
(ends)
NN
NN
N &O, check to be sure the moulded plastic backer
aligns with the 4-Position Spring Hanger Bracket
DD
DD
D as shown. These items are
shipped assembled, in the unlikely event they should become detached during
shipment, simply take the plastic backer, align with the holes in the metal bracket
and snap together to create an assembly as shown in the Hardware Parts Diagram.
IMPORTANT! All four plastic tabs on each moulded plastic backer should project
toward the metal hooks on 4-Position Spring Hanger Brackets
DD
DD
D. If you should
find a tab on an uninstalled 4-Position Spring Hanger Bracket not so projected,
simply use a screwdriver to push tab forward until it contacts the metal hook. If
a plastic tab is not projected on a factory installed 4-Position Spring Hanger Bracket
simply place a small slotted screwdriver underneath the plastic tab and pull
forward until it contacts the metal hook. Attach a 4-Position Spring Hanger Bracket
DD
DD
D,
(2 piece assembly)
, to both Headboard
NN
NN
N & Footboard
OO
OO
O with Slotted/Phillips
Wood Screws
EE
EE
E, to be positioned exactly as the ones already factory installed.
Attach Angle Brackets
II
II
I with Slotted/Phillips Wood Screws
EE
EE
E to Headboard
NN
NN
N
and Footboard
OO
OO
O, to be positioned exactly as the ones already factory installed.DO
NOT REMOVE 4-POSITION SPRING HANGER BRACKETS OR ANY OTHER
HARDWARE ITEM ATTACHED WITH SLOTTED/PHILLIPS WOOD SCREWS
EE
EE
E.
STEP 1 - DIAGRAM 1: ATTACH OF 4-POSITION S PRING H ANGER B RACKETS AND A NGLE B RACKETS.
EE
EE
E
EE
EE
E
II
II
I
DD
DD
D
Factory
installed
OO
OO
O
Holes to
receive
Slotted/
Phillips
Wood
Screws
EE
EE
E
DD
DD
D
1
15061,16101,16151,16191,16281