Filter
Top Products
Z22
R91
CLOSE
EDGE
R94
R92
R93
L1
R1
R2
Z1
K5
K6
K2
F3
10A 32V
D1
Ø
OPEN EDGE/
PHO T O
OPEN
PHO T O
CLOSE
PHO T O
R227
R2
Ø
7
Z2
Ø
R223
P1
Z9
Z8
F2
F6
D4 R9
R224
U4
CONTROL
INPUTS
FORCE
TIMER TO
CLOSE
OFF MAX
OPEN
SINGLE BUTTON
RESET
STOP
SHADOW
INTERRUPT
CHGR
OVLD
COM
COM
COM
LOOP
INPUTS
POWER
F1 20A 32V
R35
D9
Z3
Z4
U3
C11
C13
C12
D15
C2 R4
R1
Ø
1
R1
ØØ
R9
Ø
Q9
K1
R196
Q22
D8
K3
D22
C4
ACCESSORY
OVLD
MOV1
MOV2
Z12
24 VAC/
SOLAR
INPUT
GATE 2
ACCESSORY
POWER
MAGLOCK
ALARM
GATE 1
C
C
NC
NO
NO
GRN
WHT
YEL
BLU
BLU
RED
BRN
GRN
WHT
YEL
RED
BRN
GRN
WHT
YEL
BLU
RED
BRN
F4
10A 32V
F7
24V
COM
OVLD
GATE 2
DIAGNOSTIC
GATE 1
GATE 2
J4
LEARN
XMITTER
ON
R1
To Add or Reprogram a Remote Control
(not provided)
1. Press LEARN XMITTER button and release (LED will
light up).
2. Press remote button, the LED will fl ash, alarm output
will activate twice.
3. Repeat steps 1 and 2 until all remote controls are
programmed (50 remote controls maximum).
NOTE: For highest level of security, we recommend the Security
®
line of products. Refer to Accessories.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
To prevent possible serious injury or death from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep gate or garage door in sight until completely
closed. Never permit anyone to cross path of moving gate or
door.
To Add a Wireless Keyless Entry
(not provided)
1. Press LEARN XMITTER button and release (LED will
light up).
2. Enter a four digit personal identifi cation number (PIN)
of your choice on the keypad.
3. Then press ENTER, the LED will fl ash, alarm output will
activate twice.
To Erase All Codes
To deactivate any unwanted remote controls or keyless
entries, fi rst erase all codes:
Press and hold the LEARN XMITTER button on control
board until the learn indicator light goes out (approximately
6 seconds). All previous codes are now erased.
Reprogram each remote control or keyless entry you wish
to use.
Remote Control LEARN XMITTER Button
Programming 36
LEARN
XMITTER
Make sure the rubber seal around the cover is intact and close the cover. Secure the control box cover with screws (4).
Installation is complete.