A SERVICE OF

logo

Open as PDF
next previous
24
Operation
8
The EXTERNAL BATTERY TYPE selection screen will appear.
EXTERNALBATTERYTYPEreferstotheabilityfortheUPStobecomeawareofwhichexternal
battery pack is connected to the UPS. Setting the external battery configuration enhances
the accuracy of the MINUTES RUNTIME countdown during power failure conditions. The LCD
interface supports no external batteries with the factory configuration of BP0. Two additonal
LCD configurable external battery pack options are available under the user selection of BP0,
BP1&BP2.SeethetabletodeterminewhetherBP1orBP2appliestoyourexternalbattery
pack. If your battery pack is not listed or you are using more than one of any supported
externalbatterypack,youmustuseTrippLite’sEXTERNALBATTERYCONFIGURATIONTOOL
softwareavailablefordownloadatthislink:http://www.tripplite.com/bpconfig
NOTE: Use the BP0 setting if you plan to use the EXTERNAL BATTERY CONFIGURATION TOOL
software. After the software configuration is run, the UPS LCD screen will report “BPC”.
The UPS can be reset from BPC to BP0, BP1 or BP2 settings via the LCD screen, but once
the new configuration is set, you’ll need to run EXTERNAL BATTERY CONFIGURATION TOOL
software again to re-configure back to the unique BPC setting.
ACCEPT AND ADVANCE VIEW ALTERNATE SETTINGS LEAVE UPS SETUP MODE
To ACCEPT the current value
& ADVANCE to the next
configuration screen, press
the ON/SELECT button (less
than 1 second).
ToVIEWALTERNATESETTINGS,
press the SETUP BUTTON
repeatedly (under 1 second
each).
AVAILABLE VALUES
BP0 (factory), BP1, BP2
(BPC reflects a software set
configuration)
To leave UPS setup mode,
PRESSandHOLDtheSETUP
BUTTON (about 3 seconds).
UPS MODEL BP0 BP1 BP2 ALL OTHER BATTERY PACK CONFIGURATIONS
SU1000XLCD
No BP Qty1BP24V15RT2U Qty1BP24V28-2U UseEXTERNALBATTERYCONFIGURATIONTOOLsoftware
SU1500XLCD
No BP Qty1BP48V24-2U Qty1BP48V60RT3U UseEXTERNALBATTERYCONFIGURATIONTOOLsoftware
SU2200XLCD
No BP Qty1BP48V24-2U Qty1BP48V60RT3U UseEXTERNALBATTERYCONFIGURATIONTOOLsoftware
SU3000XLCD
No BP Qty1BP72V15-2U Qty1BP72V28RT3U UseEXTERNALBATTERYCONFIGURATIONTOOLsoftware
9
The VIEW IP ADDRESS selection screen will appear.
TheVIEWIPADDRESSisadisplayfieldthatenablesviewingofthecurrentUPSIPaddresswhen
the SNMPWEBCARD option is in use. The UPS is only capable of displaying a IPv4 level IP address
whenconfiguredwiththeSNMPWEBCARD.IfVIEWIPADDRESSisattemptedforIPv6levelIP
address or for a UPS configuration without the SNMPWEBCARD, the LCD screen will report NA.
ACCEPT AND ADVANCE VIEW ALTERNATE SETTINGS LEAVE UPS SETUP MODE
ToADVANCEtobacktothe
OUTPUT VOLTAGE selection
screen, press the ON/SELECT
button (less than 1 second).
ToVIEWIPaddressinformation
in 3 digit segments, press the
SETUP button repeatedly (less
than 1 second).
To leave UPS setup mode,
PRESSandHOLDtheSETUP
BUTTON (about 3 seconds).
13-03-138 93-3168-EN.indd 24 3/28/2013 1:05:44 PM