Yamaha MGP-24X Musical Toy Instrument User Manual


  Open as PDF
of 20
 
MGP Series Specifications
MGP32X MGP24X
MGP16X MGP12X
General Specifications
MGP32X MGP24X MGP16X
MGP12X
*1 Noise is measured with a A-Weighting filter. *2 Crosstalk is measured with a 1 kHz band pass filter.
*3 Maximum voltage gain is measured under the condition that all faders and GAIN knobs are at
maximum. PAN/BAL knob is panned hard left or right.
0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms.
*1 Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to
maximum level. (all faders and level controls are at maximum position.)
*2 XLR-3-31 type connectors are balanced.(1=GND, 2=HOT, 3=COLD)
*3 Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *4 Phone Jacks are unbalanced.
*5 Phone Jacks are unbalanced.(Tip=Out, Ring=In, Sleeve=GND) *6 XLR-3-31 type connectors is unbalanced.
0 dBu=0.775 Vrms, 0 dBV=1 Vrms
*1 Sensitivity: The lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to
maximum level. (All faders and level controls are at their maximum position.)
*2 Combo jacks are balanced (1&Sleeve=GND, 2&Tip=HOT, 3&Ring=COLD)
*3 XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*4 Phone jacks are unbalanced. *5 Phone jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND)
0 dBu=0.775 Vrms, 0 dBV=1 Vrms
*1 XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2 Phone jacks are impedance balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*3 Phone jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND)
*4 Phone jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms.
*1 XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2 Phone Jacks are impedance balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*3 Phone Jacks are unbalanced.(Tip=Out, Ring=In, Sleeve=GND)
*4 Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*1 Noise is measured with an A-Weighting filter. *2 Crosstalk is measured with a 1 kHz band pass filter.
*3 Maximum voltage gain is measured under the condition that all faders and GAIN controls are at
maximum. PAN/BAL controls are panned hard left or right.
NET Weight
19kg (41.9lb)
Input channel EQ
High
Mid
Low
FX1:REV-X
FX2:SPX
0.02%
+0.5/-1.0dB 20Hz - 20kHz, refer to the nominal output level @1kHz
-128 dBu Equivalent Input Noise/-94 dBu Residual Output Noise
20 Hz – 20 kHz Rs = 150Ω Input Gain = Maximum
MIC: 24
LINE: 24 mono + 4 stereo
CH INSERT IN: 24
RETURN: 1 stereo
MIC: 16
LINE: 16 mono + 4 stereo
CH INSERT: 16
RETURN: 1 stereo
STEREO OUT: 1
AUX SEND: 6
CH INSERT OUT: 24
MONITOR OUT: 1
GROUP OUT: 4
PHONES: 1
ST CH INSERT: 1
Matrix out: 2
Mono out: 1
STEREO OUT: 1
AUX SEND: 6
CH INSERT OUT: 16
MONITOR OUT: 1
GROUP OUT: 4
PHONES: 1
ST CH INSERT: 1
Matrix out: 2
Mono out: 1
-74dB @ 1kHz
48V phantom power per channel
MIC INPUT (100Hz 12dB/oct)
CH9-24 CH9-16
control x 1 (Gain/Threshold/Ratio)
8 PROGRAM, PARAMETER control
16 PROGRAM, PARAMETER control
4 ×12 segments LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30dB)
PEAK lights if the signal comes within 3dB of the clipping level.
PEAK indicator (red), SIG indicator (green)
Peak lights if the signal comes within 3dB of the clipping level.
100-240V 50Hz/60Hz
86W max
1,027×169×565mm (40.4×6.7×22.2")
15.5kg (34.2lb)
76W max
819×169×565mm (32.2×6.7×22.2")
Total Harmonic Distortion
20Hz-20kHz@ +14dBu
Frequency Response
Noise
INPUT Connectors
OUTPUT Connectors
Phantom Power
Crosstalk
Input HPF
Compressor (COMP)
8kHz: shelving
250Hz-5kHz: peaking (MGP32X:CHs 1-24, 29-32 MGP24X:CHs 1-16, 21-24) 2.5kHz: peaking (MGP32X:CHs 25-28 MGP24X:CHs 17-20)
125Hz: shelving
9.0kg (19.8lb)
0.02%
+0.5/-1.0dB 20Hz - 20kHz, refer to the nominal output level @1kHz
-128 dBu Equivalent Input Noise/-102 dBu Residual Output Noise
20 Hz – 20 kHz Rs = 150Ω Input Gain = Maximum
MIC: 10
LINE: 8 mono + 4 stereo
CH INSERT: 8
RETURN: 1 stereo
2TR IN: 1 stereo
STEREO OUT: 1
AUX SEND: 2
CH INSERT OUT: 8
REC OUT: 1
MONITOR OUT: 1
GROUP OUT: 4
PHONES: 1
MIC: 6
LINE: 4 mono + 4 stereo
CH INSERT IN: 4
RETURN: 1 stereo
2TR IN: 1 stereo
STEREO OUT: 1
AUX SEND: 2
CH INSERT OUT: 4
REC OUT: 1
MONITOR OUT: 1
GROUP OUT: 4
PHONES: 1
-74dB @ 1kHz
48V phantom power per channel
MIC INPUT (100Hz 12dB/oct)
CH1-8 CH1-4
control x 1 (Gain/Threshold/Ratio)
8 PROGRAM, PARAMETER control
16 PROGRAM, PARAMETER control
2 x 12points LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30dB)
PEAK lights if the signal comes within 3dB of the clipping level.
PEAK indicator (red), SIG indicator (green)
Peak lights if the signal comes within 3dB of the clipping level.
iPod, iPhone exclusive
100-240V 50Hz/60Hz
55W max
447×143×495mm (17.6×5.6×19.5")
7.5kg (16.5lb)
45W max
348×143×495mm (13.7×5.6×19.5")
8kHz: shelving
250Hz-5kHz: peaking (MGP16X: CH1-8,13-16 MGP12X: CH1-4,9-12) 2.5kHz: peaking (MGP16X: CH9-12 MGP12X: CH5-8)
125Hz: shelving
Internal
Digital Effect
LED Level Meter
Pre MONITOR Level
Signal Indicator
USB Audio USB IN/OUT
Power Supply
Power Consumption
Dimensions (W × H × D)
USB Device, iPod / iPhone
ANALOG INPUT SPECIFICATIONS ANALOG OUTPUT SPECIFICATIONS
ANALOG INPUT SPECIFICATIONS ANALOG OUTPUT SPECIFICATIONS
Input terminal
Actual
source
impedance
For use with
nominal
Input level
Connector
PAD GAIN
Sensitivity
*1
Nominal
Max.
before clip
MONO CH INPUT
MGP32X: 1–24
MGP24X: 1–16
0
-60dB
3kΩ
50-600Ω
Mics
-80 dBu
(0.078 mV)
-60 dBu
(0.775 mV)
-40 dBu
(7.75 mV)
XLR-3-32 type*
2
Phone jack*
4
-16dB
-36 dBu
(12.3 mV)
-16 dBu
(123 mV)
+4 dBu
(1.23 V)
26dB
-34dB
600Ω
Lines
-54 dBu
(1.55 mV)
-34 dBu
(15.5 mV)
-14 dBu
(155 mV)
Phone jack*
3
+10dB
-10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
STEREO CH INPUT
MGP32X: 25–32
MGP24X: 17–24
-34dB
10kΩ
600Ω
Lines
-54 dBu
(1.55 mV)
-34 dBu
(15.5 mV)
-14 dBu
(155 mV)
Phone jack*
4
RCA Pin Jack
+10dB
-10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
MONO CH INSERT INPUT
MGP32X: 1–24
MGP24X: 1–16
10kΩ
600Ω
Lines
-20 dBu
(77.5 mV)
0 dBu
(0.775 V)
+20 dBu
(7.75 V)
Phone Jack*
5
ST CH INSERT INPUT L,R
10kΩ
600Ω
Lines
-20 dBu
(77.5 mV)
0 dBu
(0.775 V)
+20 dBu
(7.75 V)
Phone Jack*
5
TALKBACK INPUT
10kΩ
50-600Ω
Mics
-66 dBu
(0.389 mV)
-50 dBu
(2.45 mV)
-30 dBu
(24.5 mV)
XLR-3-31 type*
6
Output terminal
Actual
source
impedance
For use with
nominal
Output Level
Connector
Nominal
Max.
before clip
ST OUT [L,R] 75Ω 600Ω Lines
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
XLR3-32 type*
1
Phone jack*
4
MONO OUT 75Ω 600Ω Lines
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
XLR3-32 type*
1
GROUP OUT (1-4) 150Ω 10kΩ Lines
+4 dBu
(1.23 V)
+20 dBu
(7.75 V)
Phone jack*
2
AUX SEND (1-6) 75Ω 600Ω Lines
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
XLR3-32 type*
1
MATRIX OUT (1, 2) 150Ω 10kΩ Lines
+4 dBu
(1.23 V)
+20 dBu
(7.75 V)
Phone jack*
2
MONO CH INSERT OUT
MGP32X: 1–24
MGP24X: 1–16
75Ω 10kΩ Lines
0 dBu
(0.775 V)
+20 dBu
(7.75 V)
Phone jack*
3
ST CH INSERT OUT [L,R] 75Ω 10kΩ Lines
0 dBu
(0.775 V)
+20 dBu
(7.75 V)
Phone jack*
3
MONITOR OUT [L,R] 150Ω 10kΩ Lines
+4 dBu
(1.23 V)
+20 dBu
(7.75 V)
Phone jack*
2
PHONES OUT 150Ω 40Ω Phones 3mW 75mW ST Phone Jack
Input terminal
Actual
source
impedance
For use with
nominal
Input level
Connector
PAD GAIN
Sensitivity
*1
Nominal
Max.
before clip
MONO CH INPUT
MGP16X: 1–8
MGP12X: 1–4
0
-60dB
3kΩ
50-600Ω
Mics
-80 dBu
(0.078 mV)
-60 dBu
(0.775 mV)
-40 dBu
(7.75 mV)
Combo jack*
2
-16dB
-36 dBu
(12.3 mV)
-16 dBu
(123 mV)
+4 dBu
(1.23 V)
26dB
-34dB
600Ω
Lines
-54 dBu
(1.55 mV)
-34 dBu
(15.5 mV)
-14 dBu
(155 mV)
+10dB
-10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
STEREO CH INPUT
MGP16X: 9–12
MGP12X: 5–8
-60dB
3kΩ
50-600Ω
Mics
-80 dBu
(0.078 mV)
-60 dBu
(0.775 mV)
-40 dBu
(7.75 mV)
XLR-3-31 type*
3
-16dB
-36 dBu
(12.3 mV)
-16 dBu
(123 mV)
-6dBu
(389mV)
-34dB
10kΩ
600Ω
Lines
-54 dBu
(1.55 mV)
-34 dBu
(15.5 mV)
-14 dBu
(155 mV)
Phone jack*
4
+10dB
-10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
STEREO CH INPUT
MGP16X: 13–16
MGP12X: 9–12
-34dB
10kΩ
600Ω
Lines
-54 dBu
(1.55 mV)
-34 dBu
(15.5 mV)
-14 dBu
(155 mV)
Phone jack*
4
RCA pin jack
+10dB
-10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
MONO CH INSERT IN
MGP16X: 1–8
MGP12X: 1–4
10kΩ
600Ω
Lines
-20 dBu
(77.5 mV)
0 dBu
(0.775 V)
+20 dBu
(7.75 V)
TRS Phone Jack*
5
RETURN (L, R) 10kΩ
600Ω
Lines
-12 dBu
(195 mV)
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
Phone Jack*
4
2TR IN [L,R] 10kΩ
600Ω
Lines
-26 dBV
(50.1 mV)
-10 dBV
(0.316 V)
+10 dBV
(3.16 V)
RCA Pin Jack
Output terminal
Actual
source
impedance
For use with
nominal
Output Level
Connector
Nominal
Max.
before clip
ST OUT [L,R] 75Ω 600Ω Lines
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
XLR3-32 type*
1
Phone jack*
4
GROUP OUT (1-4) 150Ω 10kΩ Lines
+4 dBu
(1.23 V)
+20 dBu
(7.75 V)
Phone jack*
2
AUX SEND (1, 2) 75Ω 600Ω Lines
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
XLR3-32 type*
1
FX SEND (1, 2) 150Ω 10kΩ Lines
+4 dBu
(1.23 V)
+20 dBu
(7.75 V)
Phone jack*
2
MONO CH INSERT OUT
MGP16X: 1–8
MGP12X: 1–4
150Ω 10kΩ Lines
0 dBu
(0.775 V)
+20 dBu
(7.75 V)
Phone jack*
3
REC OUT [L,R] 600Ω 10kΩ Lines
-10 dBV
(0.316 V)
+10 dBV
(3.16 V)
RCA Pin Jack
MONITOR OUT [L,R] 150Ω 10kΩ Lines
+4 dBu
(1.23 V)
+20 dBu
(7.75 V)
Phone jack*
2
PHONES OUT 100Ω 40Ω Phones 3mW 75mW ST Phone Jack
15
Power up your rig with
Yamaha powered loudspeakers
 previous next