Filter
Top Products
Finishing Assembly
Place a standard full-size crib
mattressat least 51
5
/
8 in. (131
cm) long by 27
1
/4 in. (69 cm)
wide by 4 in. (10 cm) thickon
finished toddler bed frame. The
mattress must be placed so the two mattress retainers
on frame are outside of the mattress to prevent it from
moving. Your toddler bed is now ready to use.
5
606-4-00 606198
6 87
Bumps
Step 1.
Begin by attaching frame to the
footboard.
Stand footboard at one end of the
metal frame with Graco
®
name fac-
ing out and four plastic bumps of
the footboard facing toward frame.
Holding footboard upright, grasp
the two side tubes as shown and
lift carefully. Rest ends of side
tubes on the footboard.
Step 2.
Insert two T-nuts through two
holes in side tubes and into foot-
board tube as shown. Place bolts
into holes on outside of footboard
tubes and into T-nuts. Tighten
bolts with enclosed hex wrench.
Repeat on other side of footboard.
Step 3.
Attach headboard in the same
way. The side with the deeper
recess should be facing the bed
as shown.
After both endboards have been
attached to frame, use the hex
wrench to FIRMLY TIGHTEN all
eight bolts into their T-nuts.
Step 4.
To create star panel, first twist
glow-in-the-dark pieces off the
plastic stem (immediately
discard stem). From the back
of the decorative panel, insert
pieces by pushing firmly in the
center of each one. (There are
three different sizes of stars and
star openings.) Check that all
stars are used and no holes are
left empty.
Step 5.
Hold panel in place on headboard
while inserting five screws through
back of headboard. (The plastic in
the screw holes may need to be
removed.) Tighten screws securely,
but do not over-tighten.
T-nut
Bolt
Hex
wrench
Attaching the Headboard and Footboard
T-nut
Step 1.
Snap the mattress retainers
onto the center of the side
tubes. The ribs of each retainer
should face the inside of the
bed frame. Line up the holes of
the mattress retainers with the
small holes in the side tubes.
Step 2.
Fasten each mattress retainer
to the side tubes with one T-nut
and bolt. T-nut must be on
inside of frame. Tighten bolts
and T-nuts with the hex wrench.
Step 3.
Position mattress support with
printed side up as shown. Fold
edges down at creases, and
place on bed so notches in
edges fit over the crossbars.
Hex wrench
Bolt
Attaching the Mattress Retainers
Do not use toddler bed without
mattress retainers. Mattress may slide.
Ribs
Instructions for ordering replacement parts:
Complete form below. Your toddler bed model number MUST be
included on the form to ensure proper replacement parts. Your model
number can be found on the label on the side tube of your toddler bed.
Payment must accompany your order.
Parts List:
Side tube ...............................................
Crossbar ................................................
Long leg ................................................
Short leg ................................................
Foot .......................................................
Glow-in-the-dark pieces ........................
Decorative panel ...................................
Hardware ...............................................
Mattress support ...................................
Mattress retainer ...................................
Headboard .............................................
Footboard ..............................................
Left bed rail
(as seen from behind headboard) ..
Right bed rail
(as seen from behind headboard)
Price:*
$ 8.00 (each)
$ 5.00 (each)
$ 7.00 (each)
$ 5.00 (each)
$ 5.00 (set of 4)
$ 5.00
$ 6.00
$ 5.00
$10.00
$ 5.00 (each)
$12.00
$12.00
$10.00
$10.00
* Prices subject to change without notice.
Return the form below with payment to:
GRACO CHILDRENS PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
ELVERSON, PA 19520
IF YOU NEED HELP: If you have any questions or if you
need any part not listed, please call toll-free: 1-800-345-4109
or visit our Internet website, www.gracobaby.com.
This side
faces bed
Step 1.
There are left and right bed rails.
When installed correctly, the note
on the bed rails, THIS SIDE
MUST FACE MATTRESS, will
be to the inside of the bed.
Snap bed rails on bed side
tubes as shown.
Step 2.
Lift bed rails and slide them to
the inside of the headboard.
Snap to headboard as shown.
Mattress retainer will fit in the
recessed area in the bed rails.
Be sure bed
rails are secure. Bed rails must
be attached to headboard on
the inside of the post.
Step 3.
Repeat on other side. Both bed
rails must be used. Do not rely
on wall to keep child in bed. See
warnings.
Fold edges
down
Attaching the Bed Rails
Assembling the Frame
Step 1.
Line up the side tubes and
crossbars on the floor as
shown at right. It may be
helpful to brace one side tube
against a wall or stationary
object. Holes in side tubes
must face each other.
Step 2.
Insert ends of the crossbars
into holes in the side tubes.
Mattress
retainer
Assembling the
Headboard and Footboard
Step 1.
Legs have a small side hole near
one end. For each leg, push end
with side hole firmly down into
a plastic foot. Side hole must be
covered by foot. It may be
necessary to tap foot on a hard
surface to get it all the way on.
Step 2.
Assemble headboard and long
legs. Push open end of one long
leg onto plastic plug under knob
on one side of headboard.
Then push leg sideways so the
rectangular plug on lower side
of headboard goes into hole on
side of the leg.
Attach other long leg in the
same way to other side of the
headboard.
Assemble the footboard and
short legs the same way.
Step 3.
Insert a hex head screw into
lowest hole on each leg and
into plastic head- or footboard.
Tighten screw securely with the
included hex wrench, but do
not over-tighten.
Repeat for other three legs.
CHECK that all four legs are
securely attached to the
head- and footboards by
pulling on the legs.
Screw
Hex
wrench
Side hole
Model No. (required)
Serial No.
(required)
SHIP TO:
Name
Address
City, State, Zip
( )
Telephone
Check enclosed
(payable to Graco Childrens
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Account #:
Expiration date:
Signature:
Side tube
Crossbar
Long leg
Short leg
Foot
Glow-in-dark pieces
Decorative panel
Hardware
Mattress support
Mattress retainer
Headboard
Footboard
Left bed rail
Right bed rail
Subtotal:
Shipping
& handling*: $5.00
6% sales tax
(PA only):
Total:
*$15.00 outside the continental U.S.