Filter
Top Products
10 11 12
9
832-6-00
To Change to Swivel
or Non-swivel Wheels
Front swivel wheels lock for use on uneven surfaces
such as grass, stones or gravel.
Before locking swivels, first push stroller forward a few
feet to ensure that the wheels are correctly positioned.
Push lock button UP to lock
the swivels.
Push button DOWN to release.
Turn swivel to check that it is
locked or released.
Front Canopy:
Push both canopy brackets
down at the same time into
openings on stroller frame.
To Adjust Canopies
Push or pull either canopy to
desired position.
Front canopy pivots to the front
or to the rear.
To Adjust Seat Backs
Step 1.
Place crotch strap between legs and
fasten both belt buckles together.
Step 2.
Adjust belt at both buckles as needed to get a snug fit
around your child.
Step 3.
Squeeze sides of buckles to release.
To Secure Your Child
Avoid serious injury from falling or
sliding out. Always use seat belt.
To Unfold Stroller
Step 1.
Push down on the storage latch.
Step 2.
Unfold stroller as shown.
Be certain
the stroller is fully erected and
latched before allowing your
child near the stroller.
Front seat back has one recline
position. Rear seat back has
three, including fully reclined
carriage position.
To recline either the front or rear
seat back, push back of seat
slightly forward while pulling up on
wire as shown to unlock. Recline
seat back to the desired position.
Child may slip into leg openings and
strangle. Never use rear seat in a reclined carriage
position unless closure flap is properly secured.
!
Fabric side panels must be snapped at front of both
armrests.
!
Two lower hook/loop tabs must be threaded through
buttonholes in fabric side panels and tightly fastened.
!
Two upper hook/loop tabs must be threaded through
plastic slots at front of armrests and tightly fastened.
Snaps
Insert tabs through
fabric buttonholes
and plastic slots
Rear Canopy:
Step 1.
Snap canopy mounts between
rings on plastic sleeves above
the armrests.
Step 2.
Fasten two hook tabs on rear
canopy flap to the loop tabs on
canopy. Repeat on other side.
To remove canopy, reverse
above steps.
To Install Canopies
Before installing the canopies, first identify the front and
rear canopies according to the pictures above. Position both
canopies with the large sewn tunnel toward the front.
Rear canopy
(with rear flap)
Front canopy
(no flap)
To Attach the Graco
®
Safety Seat
(sold separately)
Improper use of this stroller with a
carrier may result in serious injury or death.
Do not use this stroller with a safety seat that is not
the Graco
®
brand.
Read the owners manual provided with your Graco
®
safety seat before using the seat with this stroller.
If you do not have the owners manual for the
Graco
®
safety seat, call Graco at 1-888-224-6549.
Make sure the stroller is fully assembled according to the
preceding instructions, with the front tray or rear armbar
(on certain models) attached. Do not use a safety seat
in any stroller seat that does not have a tray or arm
bar installed.
Step 1.
If the stroller is folded, unfold it. Fully recline the back
of the stroller seat that is to be used with a safety
seat. Push down on the tray or arm bar to be sure
it is securely attached to the stroller.
Step 2.
Unbuckle the stroller seat belt, move the buckles all the
way to the loose end of the seat belt webbing, and
hang buckles outside of the stroller.
To Put Children in the Stroller
Avoid rearward tipping. Placing weight
only in the rear of this stroller could cause the stroller
to tip backwards.
!
Always place the heaviest child
or the heaviest child/carrier
combination in the front seat.
!
Always place the front child first.
When unloading, remove the
rear child first.
!
Never place purses, shopping
bags or accessory items on the
handle or canopy.
Place more weight
in front seat
To Use Brakes
Always apply
both brakes to park stroller.
Push DOWN to park.
Check to make sure brakes are
on by trying to push the stroller.
Lift UP to stroll.