Filter
Top Products
*
On certain models
5
760-1-99
6 87
To Assemble Front Wheels*
Place parts in order on front axle as shown. Push
red retainer onto axle BEFORE attaching white cap.
Repeat on other side.
Be sure cap is snapped securely over red retainer.
Axle
Wheel
Cap (white)
Attach AFTER
retainer is on axle
Retainer (red)
Wide end toward wheel
To Assemble Front Swivel Wheels*
Step 1.
Line up pin with a wheel
assembly as shown.
Step 2.
Push wheel assembly onto pin
until it snaps in place.
Step 3.
Repeat for other wheel
assembly.
Pull firmly on each wheel
assembly to be sure the
wheel assemblies are
securely attached.
To prevent serious injury or
death from choking, remove
and IMMEDIATELY discard
the plastic end caps on the
front leg pins.
End cap
To Assemble Rear Wheels
Place parts in order on rear axle as shown. If the hub
adapter will not go against the rear axle mount, push the
brake wire down and check to make sure the hub adapter is
aligned in the wheel correctly.
Rear
axle
Hub adapter
toward inside
Be sure cap is snapped securely over red retainer.
Retainer (red)
Wide end toward wheel
Wheel
Cap (white)
Attach AFTER
retainer is on axle
To Assemble Front Axle
*
Step 1.
Put both front axle mounts on
the frame. (The pointed side of
the axle mount faces the rear of
the stroller.)
Step 2.
Put the axle through the hole in the
axle mount and frame. It may be
necessary to twist the axle mount
slightly to get the axle into the hole.
Footrest
Pointed
side to
back
Step 4.
Pull firmly on each axle mount to be sure it is securely
attached.
HINT: If the axle mounts do not snap on the legs, they
may be facing the wrong way. Remove the axle mounts
with brake wire and face them the other way.
Step 5.
Insert rear axle (longer axle)
through holes in the rear axle
mounts. It may be necessary to
twist the axle mount slightly to
get the axle through the holes.
Axle
To Unpack Stroller
Step 1.
Flatten stroller carton to
protect floor.
Step 2.
Open stroller on carton until
locking latches on both sides
are locked as shown.
Step 3.
Push down on the footrest until
it snaps on the bar under it.
Flattened carton
Locking
latch
Step 2.
Turn stroller over as pictured above.
Step 3.
Position rear axle mount assembly and brake wire as shown.
Push assembly onto rear legs until plastic tabs snap into the
slots on the legs.
To Assemble Rear Axle
Step 1.
Push rear axle mounts onto
brake wire as shown. It is very
important to insert the brake
wire into the axle mounts
correctly. If it is not, the brakes
will not work properly.
Brake
wire slot
PARTS LIST
CHECK that you have all the parts listed below
BEFORE assembling your stroller.
If any parts are missing,
call Customer Service at 1-800-345-4109
or visit our Internet website, www.gracobaby.com.
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
Retainer
(4, 1 extra)
Front axle (short)
(on certain models)
Frame
Large wheel (4)
(on certain models)
Brake wire
Rear axle
mount (2)
Rear axle (long)
Front axle mount (2)
(on certain models)
Hub
adapter (2)
Cap
(4, 1 extra)
Retainer
(2, 1 extra)
Cap
(2, 1 extra)
Large wheel (2)
The following parts are only included
on models with front swivel wheels:
Front swivel
assembly (2)
Arm bar
(on certain models)
Childs tray
(on certain models)
OR
Parents tray
(on certain models)
Red brake
on top
Brake wire
angles toward
rear of stroller
Push rear axle
mounts onto brake wire