Burley SCD589 Baby Accessories User Manual


  Open as PDF
of 2
 
DOUBLE PASSENGER TRAILERS, ONE INFANT:
Install Baby Snuggler in center of trailer, using the two center shoulder straps and center crotch
strap.
FIGURE B Follow steps 1-7.
DOUBLE PASSENGER TRAILERS, ONE INFANT, ONE CHILD:
Install Baby Snuggler on one side of trailer, using shoulder straps and crotch strap on that side.
Follow steps 1-7, positioning infant and making Baby Snuggler adjustments before placing child
in trailer seat.
DOUBLE PASSENGER TRAILERS, TWO INFANTS:
Install Baby Snugglers using both shoulder harnesses and two outer crotch straps.
Follow steps 1-7.
FOR TRAILERS WITH RECLINING SEAT FEATURE:
For added comfort, make the following adjustments to your trailer:
1. Loosen tension on the upper and lower straps behind the trailer seat.
2. Place Baby Snuggler in trailer, with Baby Snuggler bottom toward the front of the trailer
seat. Lengthen crotch strap.
FIGURE C
3. Follow steps 1-7.
Consult your Burley trailer manual for more information about the reclining seat feature.
If you do not have a copy of your trailer instruction manual, do not use the Burley Baby Snuggler.
To replace your manual, go to http://burley. com/support/manuals_curren t.cfm.
ALWAYS SECURE CHILDREN WITH HARNESS AND LAP BELT BEFORE USE. SECURE ACCORDING TO INSTRUCTIONS ON TRAILER SEAT
LABEL AND IN OWNER’S MANUAL. CONSULT A PEDIATRICAN BEFORE USING THIS PRODUCT. NEVER LEAVE A CHILD UNOBSERVED OR
UNATTENDED. FAILURE TO DO SO COULD RESULT IN AN ACCIDENT AND SERIOUS INJURY OR DEATH.
WARNING
For use while strolling and jogging ONLY.
DO NOT USE WHILE CYCLING OR SKIING.
Recommended age: 3 to 12 months
Approximate height: 25”-30” (63-76cm)
Weight: 15-21 lbs. (7-10kg)
N ot e: The Burley Baby Snuggler can be used
in any Burley child trailer with the stroller/jogger
option and the 5-point harness system (2003 and
later), but works best on those models with seat
pad attachment strips on the child seat. For more
information, consult your Authorized
Burley Dealer or visit www.burley.com.
Installation
SOLO TRAILER, ONE INFANT:
1. Remove existing shoulder harness pad and
seat pad. Insert shoulder straps through
openings in Baby Snuggler back. Use the
lower strap openings for a shorter infant,
and the upper openings for a longer
infant.
FIGURE A
2. Insert crotch strap through opening in Baby
Snuggler bottom.
FIGURE A
3. Slide padded tubes onto shoulder straps,
with straps oriented so that FLAT parts of
male buckles face each other.
FIGURE A
4. Position infant in Baby Snuggler, with infant’s
lower back centered on the Snuggler’s
lumbar support.
5. Snap male buckles into Y-buckle, with
Y-buckle positioned at infant’s sternum.
Adjust straps so infant cannot move too far
forward in Snuggler.
FIGURE A
6. To secure head and shoulders, adjust
side tension cords and toggles. The upper
Snuggler will narrow, cradling the infant’s
head. To change angle of infant’s legs, adjust
side straps.
FIGURE C
7. Fasten and adjust lap belt snugly below the
Y-buckle, making sure infant is comfortable
and able to breathe
normally.
FIGURE B
Baby Snuggler
Installation Instructions
SINGLE PASSENGER MUST BE SEATED IN CENTER POSITION.
I MPO RTANT:
STRAPS BEHIND CHILD SEAT MUST ALWAYS BE SECURED WHEN TRAILER IS IN USE.
I MPO RTANT:
FIGURE A: Baby Snuggler Installation
FIGURE B: Baby Snuggler Installation in d’lite Trailer
FIGURE C: Baby Snuggler in Reclining Position
Seat
Belt
1. For Longer
Infant
1. For Shorter
Infant
3. Strap
Tubes
2. Crotch
Strap
Adjustable
Side Tension
Cord
Adjustable
Seat Crotch
Strap
Adjustable
Side Strap
Trailer
Front
Seat Belt
Snugly
Fastened
 previous