Filter
Top Products
User Guide
Waltz SL800E/F
INTERNATIONAL MODEL NUMBER: SL800E/F
IMPORTANT: READ THESE SAFETY INSTRUCTIONS CAREFULLY BEFORE USING
YOUR STROLLER AND KEEP THEM FOR FUTURE REFERENCE. THE SAFETY OF
YOUR CHILD DEPENDS ON IT.
Thank you for choosing Zooper.
UNLOCKING & OPENING THE FRAME
To open the stroller, first lift up on the gray colored frame
lock located on the left side of the stroller, (Fig 1).
Be sure the frame lock detaches from the metal
locking pin. Then pull up on the main stroller handle
while pushing down on the top of the secondary lock,
(Fig 2). Using your hand, push down on the front edge
of the seat to ensure the stroller frame has locked
properly in the open position. Do not push down on the
front armrest bar.
WARNING Be sure children are at a safe
distance and cannot reach moving parts whenever
opening or closing the stroller.
!
The front wheels slide into the metal ends of each
front leg tube. Press each wheel block firmly onto in
the metal end tubes until they "click" into position (Fig 3).
Check to see they have been properly installed by
pulling down on the wheel block.
It should not move from the leg tube at all. Should
there be a need to remove the front wheels, first
locate the rounded metal spring lock on the side
of the metal wheel housing. Press the spring lock in
while pulling the wheel off the front leg tube.
ATTACHING THE FRONT WHEELS TO
THE FRAME
32
ATTACHING THE REAR AXLE &
WHEELS TO THE FRAME
WARNING Do not use the stroller if the brake
levers are not facing away from the stroller and if the
locking pins are not visible as described above.
Contact the appropriate service center listed at the
back of these instructions if you have questions.
!
PRESSPRESS
To lower the backrest, lift up on the plastic lever
located in the middle of the seatback. While
holding the lever up, move the seatback down
into desired position and then release the lever
(Fig 6). To raise the backrest, push up on the back
of the seat until it clicks into the desired position.
!
WARNING Always keep your child in sight
when making these kinds of adjustments. Check the
fitting of the safety harness each time the backrest
is adjusted to be sure a snug, yet comfortable
fitting is maintained.
ADJUSTING THE SEATBACK
The rear wheels and rear axle come pre-assembled.
Insert both plastic rear wheel housings onto the rear
leg tubes of the stroller (Fig 4). Make sure the brake
levers are facing out, away from the stroller. Then
push in each locking spring located on the rear
stroller tubes. Holding the locking pin in, slide each
wheel block over the pin until it locks into place and
the silver head of the locking pin can be seen
protruding from the wheel housing (Fig 5).
Should there be a need to remove the rear wheel
assembly, push in on the locking pins while pulling
down on each wheel block.
When engaging the brakes,only press on the brake
lever located on the inside of the wheels. Never
press down on the brake ber.
4
INTERNATIONAL MODEL NUMBER: SL800E/F INTERNATIONAL MODEL NUMBER: SL800E/F
To attach the front armrest to the stroller seat, line
up the inserts of the armrest bar with the two plastic
slots on both sides of the stroller seat (Fig 7).
Slide the inserts completely into these slots,
making sure that both sides secure into a locked
position. Pull out of each side of the armrest to make
sure the armrest is properly locked into the slots.
The armrest should not release from the slots.
To remove the armrest, locate the plastic tabs
underneath where the armrest connects to the
sides of the stroller. Press in the tabs while pulling
up on the armrest.
ATTACHING THE ARMREST TO
THE STROLLER SEAT
!
The safety scarf must be used whenever the seat is in
a fully reclined position. The safety scarf is combined
with
footrest. When you use the scarf, adjust the footrest
into the upright position. Then to line up the zipper of
the footrest and the scarf and zip them
together. (Fig 8).
USING THE SAFETY SCARF WHEN
SEATBACK IS FULLY RECLINED
WARNING Your child may slip into leg
openings and strangle. Never use the stroller with
the backrest fully reclined unless this baby safety
scarf is looped around the armrest and secured
in place.
!
Fig.8
Fig.7
WARNING Never pick up your stroller by
the armrest.To avoid serious injury, ensure that
children's hands, arms, and feet are well clear
of the bumper bar before opening or closing it.
Fig.1
Fig.2
Fig.3
Fig.6
Fig.5
Fig.4
5
ATTACHING THE CANOPY
WARNING The rear panel of the canopy must
be snapped onto the seat whenever the seat is
fully reclined.
!
Zooper provides a special 5-point harness safety
system. Used properly, this harness will keep your
child seated and safe. To secure your child in the
harness, push buckles (A) and (B) into the buckle
housing (C) until the buckle prongs snap into position.
Carefully adjust slider (D) to fit snugly and comfortably
around your child see (Fig 10). Follow the same
procedure to adjust the shoulder strap. For infant use,
we recommend using the extra buckle (E) for added
security. Always re-tighten the harness when your
child is in a sit up or lay back position.
SAFETY HARNESS
INTERNATIONAL MODEL NUMBER: SL800E/F
CLOSING THE STROLLER FOR TRAVEL
OR STORAGE
Each time, before closing your stroller,
check the following:
a. Your child is clear of moving parts
b. The rear brakes have been set
c. The backrest is in the full upright position
d. The front wheels are secure in the locked mode
e. The canopy is retracted
f. All items have been removed from the basket
g. The safety scarf is discharged
To close the stroller, push in on the main folding
lock located in the middle of the stroller handle.
With the main lock held in, pull up on the secondary
lock while easing the stroller handle down, (Fig 11).
Check to be sure the red frame lock secures
to the locking pin.
LOCKLOCK
PULLPULL
Fig.11
PRESS
INTERNATIONAL MODEL NUMBER: SL800E/F
6
To attach the canopy, insert the plastic shafts into the
plastic slots located on the outside of the main stroller
tubes (Fig 9). Lift up to check that each side is locked
into position. Open the canopy by pushing down on
the plastic side canopy braces. Be sure to snap the
canopy to the seat and backrest fabric whenever the
seat is fully reclined. Retract the canopy by first pulling
up on the side braces, then pushing the canopy hood
back. The canopy can be converted to allow more air
flow through the stroller. Unzip the lower half of the
canopy from the upper half. This will leave a mesh
cover that can snap to the back of the seat.“The
canopy may also be used as a napper canopy.
Locate the zipper on the rear rib of the canopy.
When unzipped the canopy will fall forward over the
bumper bar, completely shading baby from the world.
To remove the canopy,first undo the snaps. Then press
in the release tabs, located on the plastic slots,
while pulling up on the canopy shafts.
Shoulders
Straps
A B
C
Fig.10
Fig.9
D
E
2
1
!
IMPORTANT CARE AND SAFETY INFORMATION
WARNINGS
!
1
BB
CC
DD
Avoid serious injury from falling or sliding out, always use safety harness provided.
Always engage the rear brakes when not holding onto your stroller.
Never leave your child unattended.
Never use the stroller near an open fire or exposed flame.
Never allow the stroller to be used as a toy.
Never allow more than one child at a time in the stroller, per seat.
Never hang bags or other items from the handle or on the canopy. This may cause
the stroller to become unstable.
Never use the stroller on stairs or escalators.
Do not overload the basket. Maximum load is 7 lbs. Excessive weight may cause a
hazardous unstable condition to exist.
Do not overload the canopy pocket: Maximum load is 2 lbs. Excessive weight may
create a hazardous unstable condition to exist.
Before each use, check to make sure the stroller is set up properly and that all the
wheels are properly and securely attached.
This stroller is not recommended for use with a child over 55 lbs.
This stroller is designed as a walking stroller. We do not recommend running,
roller blading, or other such activities with this stroller.
This stroller is a single stroller do not use any attachments that allow for a second
child.
It may be unsafe to use accessories other than those approved by the
manufacturer or distributor.
Do not use if any part of the stroller becomes damaged, broken, unstable or missing.
Discontinue use immediately and contact customer service.
Failure to follow these warnings and instructions could result in serious injury or death.
Never use the product in a manner inconsistent with the manufacturers instructions.
Do not fold your stroller when wet.
Machine wash removable seat and armrest covers using gentle cycle,
cold water, and a mild detergent. The canopy can only be spot washed.
Line dry fabric parts.
Never use bleach when washing.
Do not leave your stroller in direct sunlight for extended periods of time.
Clean and lubricate all moving parts on the stroller frame and wheels
as needed. Use only a penetrating silicon based lubricant.
Regularly check for loose screws, broken parts, etc. Use only Zooper
approved replacement parts available through the service centers listed below.
Wipe off any sand, salt or other corrosive residue after each use where the stroller
may be exposed to those elements.
In order to maintain the highest quality standards, the distributor reserves the
right to improve or alter any Zooper stroller design without notice or obligation to
any previous purchaser. For questions or service needs, please contact the
service center located in your country of residence. Sending in your warrantee
card will help expedite any service needs.
MAINTENANCE
6
CAR SEAT COMPATIBILITY
Although we have done our best to make the Zooper
Tango as universally compatible as possible, the infant
seat you have chosen may not fit well in the stroller. The
models that we have tested and approved are:
Evenflo On My Way
Graco Snug Ride and Safe Seat
Britax Companion
To install an infant carrier, first be sure that the infant
carrier is not attached to its permanent car base. Locate
the car seat adapter strap that was packaged with your
stroller. It should have a buckle in the center, and a clip
on each end. Next, identify the D-rings located in the hip
points of the stroller seat. Ensure that infant seat has
been removed from its permanent car base.
rd th
Step 1 Recline the stroller seat to the 3 or 4 position.
Step 2 Attach the car seat adapter strap to the stroller
Seat by clipping the ends to the D-rings. Adjust
the strap so that it is fully extended. Unbuckle the
center, and lay the ends out over the armrests of
the troller seat.
Step 3 Place the infant seat into the stroller seat, so that
the infant seat is facing the parent. Depending
On the size and design of your seat, you will
Either place it inside the bumper bar, or over the
Bumper bar.
Step 4 Bring the ends of the adapter strap back over the
infant seat, and buckle the center. The belt
Should be positioned so that it travels over the
lap of the infant seat. Some models have belt
guides located on the sides, if your model does;
make sure the strap is positioned inside these
guides.
Step 5 Tighten the strap down so that infant seat is
securely fixed into the stroller seat. Infant seat
should not lift out of the stroller seat if properly
strapped in.
INTERNATIONAL MODEL NUMBER: SL808F
PRESS