Filter
Top Products
General Specifications
0 dBu = 0.775 Vrms Output impedance of signal generator (Rs) = 150Ω
All level knobs are nominal if not specified.
Frequency Response Input to STEREO OUT
+0.5 dB/-1.0 dB (20 Hz to 48 kHz),
refer to the nominal output level @1 kHz, GAIN knob: Min
Total Harmonic Distortion
(THD+N)
Input to STEREO OUT
0.02 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min
0.003 % @ +24 dBu (1 kHz), GAIN knob: Min
Hum&Noise *1
(20 Hz to 20 kHz)
Equivalent Input Noise -128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max)
Residual Output Noise -102 dBu (STEREO OUT, STEREO LEVEL knob: Min)
Crosstalk (1 kHz) *2 -83 dB
Input Channels 10 channels: Mono [MIC/LINE]: 4, Stereo [LINE]: 3
Ouput Channels STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX (FX) SEND: 1
Bus Stereo: 1, AUX (FX): 1
Input Channel Function
PAD CH1 – CH4 26 dB
HPF CH1 – CH4 80 Hz, 12 dB/oct
COMP CH1 – CH2
1-knob compressor
Threshold: +22 dBu to -8 dBu, Ratio:1:1 to 4:1,
Output level: 0 dB to 7 dB, Attack time: approx. 25 msec,
Release time: approx. 300 msec
EQ
CH1 – CH9/10 HIGH:
Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving
CH1 – CH4 MID:
Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking
CH1 – CH9/10 LOW:
Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving
PEAK LED CH1 – CH4
LED turns on when post EQ signal reaches 3 dB below
clipping (+17 dBu)
Level Meter
Post STEREO LEVEL
Knob
2×7 -segment LED meter [PEAK (+17), +10, +6, 0, -6, -10, -20 dB]
Internal Digital Effect
(MG10XU)
SPX Algorithm 24 programs
USB Audio (MG10XU) 2 IN / 2 OUT
USB Audio Class 2.0 compliant
Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit
Phantom Power Voltage +48 V
Power Supply Adaptor
PA-10 (AC 38 VCT, 0.62A, Cable length = 3.6 m)
or equivalent recommended by Yamaha
Power Consumption 22.9 W
Dimensions (W×H×D) 244 mm×71 mm×294 mm (9.6” × 2.8” × 11.6”)
Net Weight MG10XU: 2.1 kg (4.6 lbs.), MG10: 1.9 kg (4.1 lbs.)
Included Accessory
AC Adaptor, Cubase AI Download Information (MG10XU),
Owner’s Manual, Precautions, Technical Specifications (this leaflet)
Optional Accessory Mic Stand Adaptor: BMS-10A
Operating Temperature 0 to +40°C
*1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter.
Analog Input Characteristics
Input Jacks
PAD
26 dB
GAIN
Trim
Position
Actual
Load
Impedance
For Use
With
Nominal
Input level
Connector
Sensitivity *1 Nominal
Max. before
clip
MIC/LINE 1 – 4
OFF
+64 dB
3 kΩ
50-600 Ω
Mics/Lines
-72 dBu
(0.195 mV)
-60 dBu
(0.775 mV)
-40 dBu
(7.75 mV)
Combo jack*2
(Balanced)
+20 dB
-28 dBu
(30.9 mV)
-16 dBu
(122.8 mV)
+4 dBu
(1.228 mV)
ON
+38 dB
-46 dBu
(3.884 mV)
-34 dBu
(15.46 mV)
-14 dBu
(154.6 mV)
-6 dB
-2 dBu
(615.6 mV)
+10 dBu
(2.451 V)
+30 dBu
(24.51 V)
LINE 5/6, 7/8
- - 10 kΩ 600 Ω Lines
-22 dBu
(61.56 mV)
-10 dBu
(245.1 mV)
+10 dBu
(2.451 V)
Phone jack *3
RCA Pin
(Unbalanced)
LINE 9/10
Phone jack *3
(Unbalanced)
0 dBu is referenced to 0.775 Vrms.
*1 Sensitivity is the lowest level that will produce an output of +4dBu (1.228V) or the nominal output level when the unit is set to maximum gain (all level knobs are
maximum position).
*2 1&Sleeve = Ground, 2&Tip = Hot, 3&Ring = Cold
*3 Tip = Signal, Sleeve = Ground
Analog Output Characteristics
Output Terminals
Actual Source
Impedance
For Use With
Nominal
Output level
Connector
Nominal Max. before clip
STEREO OUT [L, R] 75 Ω 600 Ω Lines
+4 dBu
(1.228 V)
+24 dBu
(12.28 V)
XLR-3-32 *1
Phone jack *2
(Balanced)
MONITOR OUT [L, R]
AUX (FX) SEND
150 Ω 10 kΩ Lines
+4 dBu
(1.228 V)
+20 dBu
(7.750 V)
Phone jack *2
(Impedance Balanced)
PHONES 110 Ω 40 Ω Lines 3 mW + 3 mW 100 mW + 100 mW Stereo phone jack
0 dBu is referenced to 0.775 Vrms.
*1 1 = Ground, 2 = Hot, 3 = Cold
*2 Tip = Hot, Ring = Cold, Sleeve = Ground
Digital Input / Output Characteristics
Output Terminals Format Data Length*1 Fs Connector
USB USB Audio Class 2.0 16 /24 bit
44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
USB Standard-B
*1 Data length depends on the particular audio format being used. USB Audio Class2.0: 16 / 24-bit, Yamaha Steinberg USB Driver: 24-bit
European Models
Inrush Current based on EN 55103-1:2009
1 A (on initial switch-on)
1 A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Specifications and descriptions in this document are for informational purposes only. Yamaha Corporation reserves the right to modify products or specifications at
any time without prior notice. Since specifications, equipment, and options may not be the same in every locale, please check with your Yamaha dealer.
ZJ12600
MIXING CONSOLE
Technical Specifications
See reverse side for block/level diagrams and dimensions.