Filter
Top Products
User Guide
UK
2 Attaching your child seat for use as a travel system
(this vehicle is intended for children from birth and up to 13kgs)
Verve P-Type
adaptor
Verve P-Type
socket
To remove the child
seat move the handle
to the carrying position.
Lift the lever on the
adaptors and lift the
child seat out of the
sockets (dia 2d).
IMPORTANT -
It may be necessary to
remove the adaptors
from the child seat
when installing it in
your vehicle.
If the adaptors are in
contact with the vehicle
seat cushion, remove
them.
To remove the
adaptors from the child
seat, pull the lever on
the adaptors away from
the child seat while
pulling down (dia 2e).
Repeat the process for
both adaptors.
The child seat is
compatible with
the ISOFIX base
(purchased separately).
See www.britax.eu for
further information.
Only use a P-Type child seat on this buggy when tted with a Verve P-Type socket
HANDY HINT -
You may nd it easier
to apply the brake
when tting the child
seat. Please refer to
the user guide for your
buggy.
Clip the socket onto
the chassis from the
inside. Align the bottom
edge of the socket with
the edge shown on
the chassis (dia 2a).
Rotate the xing arm.
Squeeze the housing
and xing arm together
with one hand and
snap over the hook
with the other hand.
Repeat this process for
both sockets.
Ensure that the left
hand and right hand
sockets are used on
the correct side of the
buggy.
To t the adaptor to the
child seat squeeze the
lever and insert into
the space below the
handle (dia 2b). Make
sure it is fully tted and
release the lever to
lock into place. Repeat
this process for both
adaptors.
Ensure that the left
hand and right hand
adaptors are used on
the correct side of the
child seat.
IMPORTANT -
The buggy seat unit
must be removed
before attaching your
car seat.
Lower the child seat
onto the buggy making
sure that the adaptor
on either side drops
into both the sockets on
each side of the buggy
(dia 2c). Push down
rmly. Once the seat is
engaged you will hear
a click.
Move the handle to
the rocking position.
Please refer to the user
guide for the child seat.
WARNING -
Check that the child
seat attachment
devices are correctly
engaged before use.
IMPORTANT -
Ensure your child is
harnessed at all times.
Unclip the hooks on
both sides of the buggy
(dia 1d).
Remove the seat unit
from the chassis by
sliding the base tabs
upwards and out of the
grooves.
Then slide the top tabs
upwards and out of the
grooves until the seat
unit is disengaged
(dia 1e).
To re-t the seat
unit reverse these
instructions.
HANDY HINT -
You may nd it easier
to apply the brake
before removing or
re-tting the seat unit.
Please refer to the user
guide for your buggy for
operation of the brake.
Unfasten the press
studs on the backrest
and unfasten the hook
and loop fastenings on
both sides of the seat
unit where it overlaps
the hood (dia 1a).
HANDY HINT -
You may nd it easier
to stand behind or to
the side of the buggy.
Remove the hood
and bumper bar
by simultaneously
pressing the buttons on
the mouldings on both
sides of the buggy and
slide them upwards
until they disengage
(dia 1b).
Unfasten the hook and
loop fastenings and
press studs shown by
the red circles
(dia 1c).
1 Removing or re-tting your seat unit
(the seat cover must be removed before tting the infant carrier)
B
A
BBO-662-00
A
B
1a 1b 1c 1d
B
B
A
A
1e
2b 2c
2d 2e
2a
1282.000 - Verve Adaptors & Sock1 1 10/1/07 09:15:40