Attwood Centric 2 Car Seat User Manual


 
The Centric Seating System is designed for quality boat seating, with
stationary- and swivel-mount attachment to fishing boat pedestals.
The seats are constructed of tough materials that are resistant to
moisture and corrosion.
REQUIRED FOR INSTALLATION
Adjustable wrench.
1/4" - 20 diameter stainless fasteners. Fastener types can be bolts,
or thread cutting bolts. Length must be
no longer than 1" (25mm)
long plus the thickness of the attachment base.
Four flat and four lock washers.
If installing optional 7029-1 Locking Latch:
Cordless drill and 5mm diameter drill bit.
Two (2) #68 x 3/16" tri-fold aluminum rivets with .040"-.5" grip range.
WARNING
Read installation instructions carefully before installing seats.
Improper mounting may result in serious injury.
MOUNTING SEAT TO BASE
Centric Seats can be mounted to a fixed base, pedestal base, swivel
base or slider mount.
MOUNTING SEAT (Figure 1)
NOTE: T-nuts are factory-installed. The T-nuts are 1/4" x 20-barrel
style “Propel
®
” nuts.
NOTE: Bolts must be 1/4"-20 thread,
no longer than 1" (25mm) long
plus the thickness of the mounting base.
© 2004 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com
Centric Seating System
Installation Instructions
Attwood marine hardware, navigational lighting, bilge pumps, and
other marine accessories are specified more than any other brand
by America’s best-known boat manufacturers as original equipment.
Look to Attwood for quality replacement parts and marine accessories.
SAVE THESE INSTRUCTIONS
Form Number 69341 Rev. C 04-11
3
®
Optional Latch
Latch Pocket
Back Panel
Latch Engaged
#68 Tri-Fold Rivets
(Not Provided)
Attachment Clips (3)
T-Nut (6)
Base Thickness
Lock Washer
Flat Washer
Fastener
1.Place washers on fasteners. Insert fasteners up through base and
tighten into T-nuts of the seat.
2.Attach Back Panel using three (3) attachment clips fasteners supplied.
INSTALL OPTIONAL LOCKING LATCH (Figure 2)
The Locking Latch holds the seat closed tightly. Lift the latch to release
the lock and raise the seat back.
1.Prior to installing back panel, hold the latch with Attwood
®
logo
outward. Place top end into the latch pocket.
2.Use latch as template to drill two (2) 5mm (13/64") holes in the pocket.
3.Attach latch with two (2) #68 tri-fold rivets (not provided).
4.Test latch for proper holding.
5.Attach back panel by pressing it into the cover attachment clips.
ATTWOOD LIMITED WARRANTY
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331 (“Attwood”)
warrants to the original consumer purchaser that Attwood brand products will be free
from defects in materials and workmanship under normal use and service for one year
from the date of original consumer purchases.
This limited warranty is not applicable if the product has been damaged by accident,
improper installation, unreasonable or improper use, lack of proper maintenance,
unauthorized repairs or modifications, normal wear and tear, or other causes not arising
out of defects in materials or workmanship.
Attwood products are warranted for use on pleasure boats. Any other use — including
but not limited to commercial, racing, or nonmarine use — are not covered under this
warranty. Attwood’s obligation under this warranty is limited to repair of the product at
Attwood’s plant or replacement of the products at Attwood’s option without expense to
the original consumer purchaser. Any expenses involved in the removal, reinstallation
or transportation of the product are not covered by this warranty.
The product must be returned to Attwood’s plant at the address above, postage prepaid,
and insured with proof of original purchase including date.
If Attwood is unable to replace the product and repair is not commercially practical or
cannot be timely made, or if the original consumer purchaser is willing to accept a refund
in lieu of repair or replacement, Attwood may refund the purchase price, less an amount
for depreciation. The acceptance by Attwood of any product returned or any refund provided
by Attwood shall not be deemed an admission that the product is defective or in violation
of any warranty. Products that are replaced or for which a refund is issued become the
property of Attwood.
THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY OF THIS PRODUCT.
NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1) YEAR FROM THE DATE
OF ORIGINAL CONSUMER PURCHASE. ATTWOOD SHALL NOT BE LIABLE FOR
ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER
INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion
or limitation of incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have
other rights which vary from state to state.
Figure 1
Figure 2